8. The Sprayer Circuit
A simple crop sprayer consists of a tank, pump, filters, pressure regulator and gauge, control valve and nozzles. The simple sprayer circuit shown in figure 13.5 was used in earlier days but modern electronically controlled sprayers are much more complicated. Typical sprayer circuits (see figures 13.6 and 13.7) have an induction hopper, clean water tank used to flush the system when changing chemicals, hydraulic tank agitation and controls for each section of the spray bar.
Figure 13.5 Flow diagram for a simple crop sprayer
Plate 13.9 This mounted sprayer control panel has electrically operated taps for the five-section spraybar. The pressure regulator is on the extreme right.
Figure 13.6 Flow diagram for a mounted crop sprayer with self-fill, chemical induction hopper and hydraulic agitation.
Figure 13.7 Flow diagram for a self-propelled high speed sprayer.
9. Sprayer controls
Regulations concerning the application of pesticides have, in recent years, brought about a complete change in the control of crop sprayers. Computers, solenoids and electro-hydraulics have replaced the hand levers previously used to operate various valves, taps and switches. The basic functions of the control unit are to switch the sprayer on and off, vary spraybar height, regulate spraying pressure and alter the application rate. When the sprayer is switched off, the chemical is sucked back from the nozzles to prevent them dripping and the pump circulates the chemical around the system to keep the tank contents mixed. Each section of the spraybar has a control tap so that one or more of them can be shut off when the full spraying width is not required, for example on a headland run.
Spray pressure is regulated by adjusting the pressure relief valve manually or with an electro-hydraulic valve. Some sprayers have an automatic control system which regulates the spraying pressure according to ground speed, thus maintaining constant application in any one gear. The control needs re-adjustment if a different gear is selected.
In-cab computerised control systems are available for many sprayers. These can be used to regulate application rate regardless of speed, gear and number of nozzles in use. The computer will also alter spraying rate, forward speed and distance travelled. It also provides information on the area covered, the amount of liquid sprayed and the quantity left in the tank.
Many of the on-board computer systems for crop spraying can be used at other times with fertiliser spreaders, grain drills and harvesting equipment.
10. Working Adjustments
Application rate Three factors affect the application rate of crop sprayers:
Tractor forward speed A low forward speed gives a high application rate. By changing gear to double the forward speed, the application rate will be halved.
Spraying pressure Higher application rates are obtained by adjusting the relief valve control to increase working pressure. High pressure reduces droplet size and increases the risk of the chemical being blown away by the wind (drift). This should be avoided, as drift can damage nearby crops and gardens. Spray drift is also a serious threat to the environment as it will harm trees, hedgerows, wild flowers, etc.
Nozzle size Nozzles with a large hole will give a high application rate. Smaller ones must be fitted when a reduction in application rate is required.
Once set, the application rate can be kept constant with an automatic control system. This electronic device is found on the more expensive sprayers. Some sprayers have a system of pressure compensation which avoids variations in working pressure when a section of the spraybar is turned off.
Figure 13.8 Setting the height of the spray boom.
Spray boom height. The spray boom must be level when in work. Figure 13.8 illustrates how the spray patterns from adjacent nozzles should meet above the target for even distribution of liquid across the width of the boom. When spraying weeds which are taller than the crop, the weeds must be considered the target. On most sprayers, the nozzles are spaced at 500 mm intervals along the spraybar. The height of the nozzles above the target is determined by the angle of the spray pattern. For example, nozzles with an 80 degree fan pattern and spaced at 500 mm on the boom should be about 550 mm above the target. Nozzles with 110 degree fan pattern will need to be set lower at about 350 to 400 mm above the target. When weather conditions allow, the nozzles can be set a little higher to avoid missed strips when uneven field surfaces cause spraybar bounce. The height of the spraybar is adjusted by moving it up or down on the frame. This adjustment is important because incorrect nozzle height will cause overdosing or missed strips.
Controlled Droplet Application (CDA) Sprayers
Low volume application rates can be achieved bv using rotarv atomisers instead of normal nozzles; 25 litres per hectare (10 gallons per acre is a typical application rate). Rotary atomisers are suitable for the application of most pesticides but are mainly used for horticultural spraying. CDA sprayers produce droplets of uniform and medium size, thus avoiding both the small droplets which tend to drift and the very large ones that tend to run off the leaf.
Sleeve Boom Sprayers. Sleeve boom or downward air-assisted sprayers have a collapsible pvc sleeve connected to a high-capacity fan above the spraybar. The sleeve directs a blast of air downwards and rearwards, to create a curtain of air which drives chemical from the nozzles into the crop, the principle being that air turbulence causes increased plant movement to give better coverage of the foliage being treated. Problems with spray drift are reduced with an air assisted sprayer, application rates are lower and the cost of chemical per hectare is lower than with a conventional hydraulic nozzle sprayer.
Twin fluid nozzle sprayer. This type of agricultural crop sprayer has a special design of nozzle which is supplied with both liquid and air. The liquid is conveyed to the nozzles by a conventional sprayer pump. A high volume, low pressure air supply is produced by a compressor on the sprayer. The air and liquid are mixed within the nozzle and forced through a small hole onto a deflector plate to produce a flat fan shaped spray pattern. Twin fluid nozzles give a more consistent droplet size and there is better retention of the droplets on the leaf. Because the droplets contain air they often collapse on impact with the foliage to create even smaller droplets.
Band Sprayers
These are very similar to ordinary crop sprayers but apply chemicals in narrow bands, saving expensive chemicals where overall coverage is unnecessary. Band sprayers are occasionally used with precision seeder units. A carefully calibrated and matched set of nozzles is used to apply pre-emergence weedkillers while drilling certain vegetable crops. This allows the young plants to emerge in a weed-free band to make inter-row hoeing an easier task.
Plate 13.10 Sleeve boom sprayers have tank capacities and spraying widths similar to conventional hydraulic nozzle sprayers.
Plate 13.11 An electronic control box (top right) opens and closes taps to each boom section and sequentially folds and unfolds the spray boom. The control unit and screen (bottom left) links the ground positioning satellite system to the sprayer control box.
Sprayer Controls
Protective clothing must be worn when working with hand-operated taps and valves, and the contaminated clothing must be stored in a PPE (Personal Protective Equipment) storage box before entering the tractor cab. Pesticide regulations have brought about a complete change in the way crop sprayers are now controlled in the field. If the driver is seated in a cab with an approved air filtration system and using a sprayer with electronic controls, he will only require PPE when filling, cleaning and servicing the machine.
A typical electronic sprayer control unit can be used to vary spraying pressure, switch on and off liquid flow to the spray boom and control individual spray boom sections. Some sprayers have an electric boom tilting mechanism linked to the control box which is used to keep the boom parallel with the ground when spraying on slopes. Other functions include locking the spray boom suspension system for transport, automatic tank filling and tank agitation when not spraving. More advanced control systems adjust the spray boom height and also fold or unfold the boom in a set order. When linked to GPS the computer carries out a pre-set turning sequence at the headland.
USING SPRAYERS
Before the season starts
Repair any damaged or worn parts.
Turn the pump by hand to check it has not seized.
Hitch the sprayer to the tractor and connect the pump to the power take-off shaft.
Clean the inside of the sprayer tank, remove the nozzles and then flush the machine with a tankful of clean water.
Wash and replace the filters, fit a clean set of nozzles and then spray out another tank of clean water, checking the spray pattern.
Make sure all the nozzles have the same output. To do this, run the machine and collect water from each nozzle for half a minute. By using a measuring jug to collect the water, the exact output of each nozzle can be obtained. Replace any unsatisfactory nozzles. Nozzles will wear with use and will need replacing after a time.
Check for leaks.
Carry out a static calibration test, and record the results.
Plate 13.12 Both spray booms can be individually folded in and out from the tractor seat. The outer sections can be folded in to reduce overall boom width when spraying narrow headlands.
Spraying
Set the sprayer to give the required application rate. Fit the" correct nozzles, then adjust to the specified pressure while spraying clean water.
Select the correct forward gear, to give the required speed, with the engine revolutions set to give 540 rpm at the power take-off.
Read the instructions on the chemical container. Make sure you use the correct protective clothing for the chemical you are spraying.
Partly fill the tank with water, add the chemical in the way indicated on the container, then add the required quantity of water to complete the tank mix. Do not remove the filter basket in the filler opening to speed up the procedure. After filling, agitate the contents thoroughly by pumping the tank load round the system. It will then be ready for spraying. Many sprayers have a mixing bowl, which makes filling the tank with chemical and water a much safer procedure.
Once in the field, spray round the headlands twice, then start on the main part of the field, working from one side towards the other. Direction of spraying will depend on wind direction, neighbouring crops and field shape.
To help with matching the work, a long length of stout twine can be tied on to each end of the spraybar. When turning on the headland, the end of the twine will stay in position until the spraybar passes over it on the return run. A foam marking device which drops blobs of foam from the end of the spraybar or marking stakes can be used as a guide. In some crops, the rows themselves provide the driving guide.
A tramline attachment on a grain drill provides a permanent driving guide by leaving two undrilled rows at selected intervals. The tractor wheels run on the undrilled land for all fertiliser and spray treatments during the life of the crop. For full benefit, the sprayer and the fertiliser distributor must have working widths which are multiples of the drilling width. The tramline system ensures minimum crop damage together with accurate crop protection.
Checking application rate. Accurate application of spray chemicals is most important and this can be checked or calibrated with a static test or in the field. Some sprayers can be calibrated electronically but for older machines it may be necessary to carry out the following static calibration procedure.
Field check It is a simple task to check application rate against area covered when using a tractor with a computerised monitoring system.
Sprayer maintenance
Many modern sprayers are equipped with a tank of clean water for flushing out the sprayer and removing any chemical residues. Crop sprayers without this facility require the following cleaning and maintenance procedures. Appropriate personal protective equipment (PPE) must be worn.
At the end of the day Empty the tank and partly fill it with water. Clean the sprayer inside and out, then spray the washings on waste land. Never dispose of the washings where they can harm humans, animals or fish. Finally, remove, clean and replace filters and nozzles.
At the end of the season Remove all traces of chemical. Clean and store nozzles separately. Drain the pump to prevent frost damage. Release relief valve pressure and, after making necessary repairs, store under cover.
Cleaning the sprayer. When changing chemical or preparing for storage, all traces of chemical must be removed. For thorough cleaning:
Open the drain tap and empty the tank into a collection tank ready for approved disposal at a later stage.
Scrub the machine with a stiff brush -especially the underside of the tank top -then hose down the sprayer.
Close the drain tap, remove and clean the filters, then partly fill the tank with clean water. Check the pesticide label to find out what cleaning agent, if any, should be added to the water. Pump the cleaning water round the spraver then spray it out on to the field or collect it in a tank for treatment. Then repeat this procedure.
Some machines have an extra clean water tank with a capacity of about 10 per cent of the main tank. A separate pump and hand lance are used to wash down the outside of the spraver before leaving the field.
Rinse the machine by spraying out two tanks of water.
Remove, wash and replace all filters and nozzles.
SAFETY WHEN SPRAYING
The Code of Practice for the Safe Use of Pesticides on Farms and Holdings, re-issued in 1998, and the Control of Substances Hazardous to Health Regulations 1999 apply to the use of all types of farm chemicals including pesticides, herbicides, fungicides growth regulators and sterilants. The application of pesticides with hand-held equipment, tractor sprayers and aircraft are included in the list of applicators covered by these regulations.
All people who handle or apply agricultural and horticultural pesticides in the UK must have proof of instruction in their use. The code of practice states that any person who was born after 31 December 1964 or who is providing a commercial pesticide application service must hold a Certificate of Competence.
The information given above is very basic and is only an indication of the contents of the various regulations concerning the application of pesticides. The official code of safe practice is the best source of information which you should study to find out exactly how the provisions affect you when handling or using pesticides. Some important points to remember include:
Follow the instructions on the package. Use protective clothing as directed and refer to employer's risk assessment requirements.
Check the label for an}- special washing requirements to be followed after using the product.
Dispose of empty containers safely. Wash out cans to remove any undiluted chemical.
Keep all pesticides in a locked store. Return any unused material to the store.
Do not smoke, eat or drink while spraying. Always wash before doing any of these.
Never blow at a blocked nozzle with the mouth. Keep spare clean nozzles with you. (Do not try to clear a blocked nozzle with a pin either - this will spoil it.)
Never transfer chemicals into other containers.
Clean all protective clothing after use.
Remember that pesticides can enter tractor cabs. A respirator is needed, even in modern safety cabs, for some of the more dangerous pesticides except when specialist filters are used in the cab ventilation svstem.
Plate 13.13 The land-wheel driven fluted roller metering mechanism in the granular applicator units on this 12-row root drill are set up to supply granules to three seeder units.
Granular Applicators. Crop protection chemicals can also be applied in a solid, granular form. Granular applicators will apply these granules to growing crops or in bands when planting potatoes and other seeds.
The granules are carried in small hoppers attached to a toolbar. A mechanical or pneumatic feed mechanism delivers granules to nozzles spaced across a toolbar or fixed to coulter units. The flow of granules from the hopper can be varied to give a range of application rates.
Weed wipers. Tall weeds including docks and thistles can be killed on pastures, in sugar beet and other crops with a weed wiper. This is a low cost operation compared with overall spraying. There are two types of weed wiper: one has a rope to carry the chemical and the other has a wide chemical carrying roller. Both machines apply a contact herbicide to foliage tall enough to be touched by the chemical impregnated wick or roll.
Rope weed wipers have an endless wick running on pulleys attached to a front- or rear-mounted frame. Herbicide on the wick is deposited on any weed it touches. Roller weed wipers work in a similar way.
These machines are made in various widths and the height of the wick or roller can be adjusted. The wider models of weed wiper are folded for transport.
Plate 13.14 A roller containing herbicide coats the smooth roller on this weed wiping machine with chemical which is transferred to any weeds which have grown above arable crops or to tall weeds on grassland.
Plate 13.15 This rear-mounted band sprayer can be supplied with chemical either from a front-mounted tank or from one on the toolbar.
Air-assisted Spraying
Air Blast Sprayers. Air blast sprayers have been used for many years to spray fruit trees. These units consist of a fan that is capable of producing a high volume of air flow into which the spray is dispensed. As the sprayer moves through the orchard, it blows the spray-laden air into the tree canopy, displacing the original air and depositing the spray material on the leaf surfaces Fig. 1.254. Most, but not all, horticultural sprayers use high pressure pumps (1.5–3 MPa) to produce fine droplets that are carried by the air. When low pressure pumps are used, good atomization depends on high-velocity air shear to produce fine droplets. Typically, air blast sprayers direct the air up into the tree from a ground level machine position. Tanks vary in size from 400–4000 dm3. They can apply either high or low volumes of material. Coverage will depend upon the machine and tree size. They may direct output to only one side of a row, both sides or cover double or more rows. Nozzles are typically selected to deliver a higher proportion of the discharge to the top half of the tree. This is discussed in Section 1.5.6, Orchard Spraying.
The latest air-carrier equipment uses diffusers of various shapes (turret, vertical slits, two fans–one in the standard position and a second, less powerful one, placed above) to shift the point of spray emission and the auxiliary air flow closer to the vegetation (Fig. 1.270, Section 1.5.10). On this type of equipment, it is possible to use nozzles with the same atomization characteristics across the entire boom.
Good coverage and penetration along with high spraying capacity are general characteristics of the air-blast sprayer. The high annual use rate of these sprayers requires a high level of manufacturing quality. The limitation of these sprayers is their high power requirement, and the potential for increased drift.
Figure 1.254. Air blast sprayer
Tower and Air Curtain Sprayers. There is an increasing trend today to use tower sprayers when spraying orchard trees. These sprayers are constructed to deliver air and spray material along a narrow vertical band that forms an air curtain extending from near the base of the tree to the top. The nozzles discharge closer to the tree foliage than with the conventional sprayers. This improves spray deposition and coverage over that of the conventional air blast sprayers, which attempt to blow the spray up into the treetops from the ground.
The air curtain is produced in some sprayers by use of multiple, long narrow tangential fans mounted vertically (Fig. 1.255). Other sprayers use an air discharge manifold modified to form a long narrow slot. The objective is the same: to have a more even air spray discharge in the tree, and to reduce the distance between the nozzle and target.
The advantage of the tower sprayer is more uniform spray deposition and reduced drift. This is offset by more expensive construction and reduced maneuverability.
Air-assisted Boom Sprayers. Several models of boom sprayers now are equipped with a fan and air manifold with the specific objective to improve spray deposition and reduce drift. Some models are configured with a horizontal air manifold across the boom just ahead of the nozzles. The air curtain discharged from the manifold blow downward, impinges upon the spray and helps to carry it to the target, providing turbulence for good deposition and reducing drift caused by typical atmospheric wind.
Figure 1.255. Tower-air curtain orchard sprayer.
Another approach uses flexible air ducts to conduct air from a central fan to the plants being sprayed. A spray nozzle at the end of the air duct mixes spray with the directed air, which carries it to the target plant, improving coverage and reducing drift.
Aerial Application. Aircraft are used to apply pesticides as sprays or dust, and to seed certain types of crops. A primary advantage of aircraft spraying is the speed with which fields may be covered. Under certain soil or crop conditions, applying chemicals by aircraft may be the only possible or reasonable alternative to ground applications. A disadvantage of aerial application is an increased opportunity for pesticide drift.
This method requires highly trained professional pilots and applicators and reliable aircraft equipment. Aircraft may be either fixed-wing craft, i.e., mono-wings or biplanes, or rotary wing types (helicopters). Aircraft sprayers typically have effective spray swath widths of 12–20 m. They fly at speeds of approximately 150–240 km/h at an altitude of 2–6 m while spraying.
SAFETY CHECK
Make sure that you comply with the Pesticide Application Regulations. You must have the proper training and probably need a Certificate of Competence when using pesticides. Find out which materials come within the scope of the Pesticides Regulations.
