Добавил:
Upload Опубликованный материал нарушает ваши авторские права? Сообщите нам.
Вуз: Предмет: Файл:
Навчальний посібник .doc
Скачиваний:
1
Добавлен:
01.07.2025
Размер:
5 Мб
Скачать
☆

1.3. Electrostatic Phenomena

Electrostatic charging is a process by which an insulator or an insulated conductor receives a charge.

The device that can be used to demonstrate the characteristics of electric charge is the electroscope. In its simplest form, it consists of a metal rod with a metallic bulb at one end and a pair of hanging foil “leaves”, usually made of gold or aluminum, at the other end. This arrangement is insulated from its protective glass container by a rubber cork. When a charged object is brought near the bulb, the leaves separate.

If a rubber rod is rubbed with fur, the rod will acquire a negative charge. Rubbing a glass rod with silk will give the rod a positive charge. This is called charging by friction. The transfer of charge is due to the contact between the materials and depends on the nature of the materials.

There are exist charging by contact or by conduction. “Conduction” refers to the flow of charge during the short period of time the electrons are in motion. When neutral electroscope is touched with negatively charged rod, charges are transferred to bulb and electroscope has net negative charge. Then if a negatively charged rod is brought close to the now negatively charged electroscope, the leaves will separate even further as more electrons are repelled onto them from the bulb. A positively charged rod will cause the leaves to collapse by attracting some electrons up to the bulb and away from the leaves.

An electroscope can become positively charged by a process called charging by induction. Touching the bulb with a finger grounds the electroscope – that is, provides a path by which electrons can escape from the bulb. Then when a negatively charged rod is brought close to (but not touching) the bulb, the rod repels electrons from the bulb into the finger and down into the Earth. Removing the finger while the charged rod is kept nearby leaves the electroscope with a net positive charge, because the removed electrons have no way of flowing back once the ground path is removed.

Both charging by contact and introduction involve a removal of charge from an object. However, an object can have some charge moved within it to give different regions of charge yet keep a net charge of zero. In this case, induction brings about polarization, or separation of charge.

1.4. Coulomb’s Law

In 1785 the French physicist Coulomb measured the force between two point charges as a function of distance between them. It was found that the magnitude of the electric force between two electric point charges is described by an equation called Coulomb’s Law:

The force between two charges q1 and q2 is directly proportional to the product of the charges and inversely proportional to the square of the distance r between the charges:

where 0=8,85410-12 C2/Nm2 is called the electric constant.

Forces acting upon charges are central ones, namely they are directed along the line that connects the centers of charges.

Coulomb’s Law is valid for point charges, for charged balls of radii R1 and R2 (if their charges q1 and q2 are uniformly distributed over their surfaces or volumes). Radii can be comparable with a distance between charges.

In the vector form Coulomb’s Law can be written (Fig.1.2):

In the case of like charges: q1q20, then F120 – like charges repel each other. The force F12 acts on the charge q1 from the side of the charge q2 (Fig.1.2). The force F21 acts on the charge q2 from the side of the charge q1 (Fig. 1.3).

In the case of unlike charges: q1q20, then F120 – unlike charges attract each other.

Figure 1.2

Figure 1.3

Coulomb force depends on properties of charges environment. This dependence is described by dielectric permittivity of an environment (for vacuum =1). An environment is considered as infinite and isotropic.

Coulomb’s Law for an environment with :

Coulomb’s Law for vacuum =1 :

Hence it follows: . So shows how much the Coulomb’s force in vacuum is bigger than in an environment.

LESSON 6

TEXT 6.1.: AUTOMATION

Automation is the system of manufacture performing certain tasks, previously done by people, by machines only. The sequences of operations are controlled automatically. The most familiar example of a highly automated system is an assembly plant for automobiles or other complex products.

The term automation is also used to describe nonmanufacturing systems in which automatic devices can operate independently of human control. Such devices as automatic pilots, automatic telephone equipment and automated control systems are used to perform various operations much faster and better than could be done by people.

Automated manufacturing had several steps in its development. Mechanization was the first step necessary the development of automation. The simplification of work made it possible to design and build machines that resembled the motions of the worker. These specialized machines were motorized and they had better production efficiency.

Industrial robots, originally designed only to perform simple tasks in environments dangerous to human workers, are now widely used to transfer, manipulate, and position both light and heavy workpieces performing all the functions of a transfer machine.

In the 1920s the automobile industry for the first time used an integrated system of production. This method of production was adopted by most car manufacturers and became known as Detroit automation.

The feedback principle is used in all automatic-control mechanisms when machines have ability to correct themselves. The feedback principle has been used for centuries. An outstanding early example is the fly ball governor, invented in 1 788 by James Watt to control the speed of the steam engine. The common household thermostat is another example of a feedback device.

Using feedback devices, machines can start, stop, speed up, slow down, count, inspect, test, compare, and measure. These operations are commonly applied to a wide variety of production operations.

Computers have greatly facilitated the use of feedback in manufacturing processes. Computers gave rise to the development of numerically controlled machines. The motions of these machines are controlled by punched paper or magnetic tapes. In numerically controlled machining centres machine tools can perform several different machining operations.

More recently, the introduction of microprocessors and computers have made possible the development of computer-aided design and computer-aided manufacture (CAD and CAM) technologies. When using these systems designer draws a part and indicates its dimensions with the help of a mouse, light pen, or other input device. After the drawing has been completed the computer auto matically gives the instructions that direct a machining centre to machine the part.

Another development using automation are the flex- ible manufacturing systems (FMS). A computer in FMS can be used to monitor and control the operation of the whole factory.

Automation has also had an influence on the areas of the economy other than manufacturing. Small computers are used in systems called word processors, which are rapidly becoming a standard part of the modern office. They are used to edit texts, to type letters and so on.