Добавил:
Upload Опубликованный материал нарушает ваши авторские права? Сообщите нам.
Вуз: Предмет: Файл:
UG130_002.doc
Скачиваний:
2
Добавлен:
01.05.2025
Размер:
8 Мб
Скачать
☆

Voltage Supply

Most modern keyboards and mice work equally well from a 3.3V or 5V supply. The voltage supply for the PS/ 2 port is selectable via the JP2 jumper, indicated as @ in Figure1-2, located immediately above the PS/ 2 connector along the right edge. The 3.3V setting is preferred as the FPGA’s output signals operate from the 3.3V supply. The JP2 jumper should be positioned as shown in Table6-5 by default.

Table 6-5: PS/2 Port Supply Voltage Options

PS/2 Port Supply Voltage

Jumper JP2 Setting

Some older keyboards and mice are 5V only. Consequently, the JP2 jumper should be set for 5V operation as shown in Table6-5. The Spartan-3 FPGA can tolerate 5V signals due to the 270Q series resistors on the PS/2 data and clock signals connected to the FPGA. See the schematic in Figure A-7 for more details

.Chapter 7

RS-232 Port

The Spartan-3 Starter Kit board has an RS-232 serial port. The RS-232 transmit and receive signals appear on the female DB9 connector, labeled J2, indicated as 0 in Figure 1-2. The connector is a DCE-style port and connects to the DB9 DTE-style serial port connector available on most personal computers and workstations. Use a standard straight-through serial cable to connect the Spartan-3 Starter Kit board to the PC’s serial port.

Figure 7-1 shows the connection between the FPGA and the DB9 connector, including the Maxim MAX3232 RS-232 voltage converter, indicated as 0 in Figure 1-2. The FPGA supplies serial output data as LVTLL or LVCMOS levels to the Maxim device, which in turn, converts the logic value to the appropriate R&232 voltage level. Likewise, the Maxim device converts the RS-232 serial input data to LVTLL levels for the FPGA. A series resistor between the Maxim output pin and the FPGA’s RXD pin protects against accidental logic conflicts. A detailed schematic appears in Figure A-7.

Hardware flow control is not supported on the connector. The port’s DCD, DTR, and DSR signals connect together, as shown in Figure 7-1. Similarly, the port’s RTS and CTS signals connect together.

Figure 7-1: RS-232 Serial Port

The FPGA connections to the Maxim RS-232 translator appear in Table 7-1. Table 7-1: Accessory Port Connections to the Spartan-3 FPGA

Signal

FPGA Pin

RXD

T13

TXD

R13

RXD-A

N10

TXD-A

T14

An auxiliary RS-232 serial channel from the Maxim device is available on two 0.1-inch stake pins, indicated as J1 in the schematic and 0 in Figure 1-2. The FPGA connections driving the Maxim device appear in Table 7-1 with signals RXD-A and TXD-A

.Chapter 8

Clock Sources

The Spartan-3 Starter Kit board has a dedicated 50 MHz Epson SG-8002JF series clock oscillator source and an optional socket for another clock oscillator source. Figure A-5 provides a detailed schematic for the clock sources.

The 50 MHz clock oscillator is mounted on the bottom side of the board, indicated as @ in Figure A-5. Use the 50 MHz clock frequency as is or derive other frequencies using the FPGAs Digital Clock Managers (DCMs).

• Using Digital Clock Managers (DCMs) in Spartan-3 FPGAs http:/ /www.xilinx.com/bvdocs/ appnotesZxapp462.pdf

The oscillator socket, indicated as @ in Figure 1-2, accepts oscillators in an 8-pin DIP footprint.

Table 8-1: Clock Oscillator Sources

Oscillator Source

FPGA Pin

50 MHz (IC4)

T9

Socket (IC8)

D9

Chapter 9

FPGA Configuration Modes and Functions

FPGA Configuration Mode Settings

In most applications for the Spartan-3 Starter Kit Board, the FPGA automatically boots from the on-board Platform Flash memory whenever power is applied or the PROG push button is pressed. However, the board supports all the available configuration modes via the J8 header, indicated as 0 in Figure 1-2. Table9-1 provides the available option settings for the J8 header. Additionally, the JP1 jumper setting is required when using Master Serial configuration mode, as further described in “Platform Flash Jumper Options

(JP1)”

The default jumper settings for the board are:

  • All jumpers in the J8 header are installed

  • The JP1 jumper is in the “Default” position

Table 9-1: Header J8 Controls the FPGA Configuration Mod

Configuration

Mode

<M0:M1:M2>

Master Serial <0:0:0>

Slave Serial <1:1:1>

Master Parallel <1:1:0>

Соседние файлы в предмете [НЕСОРТИРОВАННОЕ]