Voltage Regulators
There are multiple voltages supplied on the Spartan-3 Starter Kit Board, as summarized in Table 12-1.
Table 12-1: Voltage Supplies and Sources
Voltage |
Source |
Supplies |
+5V DC |
AC Wall Adapter, 5V switching power supply (0 in Figure 1-2) |
3.3V regulator Optionally, PS/ 2 port via jumper JP2 setting Pin 1 (VU) on A1, A2, B1 expansion connectors |
+3.3V DC |
National Semiconductor LM1086CS-ADJ 3.3V regulator (0 in Figure 1-2) |
2.5V and 1.2V regulators VCCO supply input for all FPGA I/O banks M ost components on the board Pin 3 on A1, A2, B1 expansion connectors |
+2.5V DC |
STMicroelectronics LF25CDT 2.5V regulator (0 in Figure 1-2) |
VCCAUX supply input to FPGA |
+1.2V DC |
1.2V regulator (0 in Figure 1-2) |
VCCINT supply input to FPGA |
Overall, the 5V DC switching power supply that connects to AC wall power powers the board. A 3.3V regulator, powered by the 5V DC supply, generates power for the 2.5V and
1.2V regulators. Similarly, the 3.3V supply feeds all the VCCO voltage supply inputs to the FPGA’s I/ O banks and powers most of the components on the board.
The 2.5V regulator, powered by the 3.3V regulator, supplies power to the FPGA’s VCCAUX supply inputs. The VCCAUX voltage input supplies power to Digital Clock Managers (DCMs) within the FPGA and supplies some of the I/ O structures. In specific, all of the FPGA’s dedicated configuration pins, such as DONE, PROG_B, CCLK, and the FPGA’s jTAG pins, are powered by VCCAUX. The FPGA configuration interface on the board is powered by 3.3V. Consequently, the 2.5V supply has a current shunt resistor to prevent back current.
Finally, a 1.2V regulator supplies power to the FPGA’s VCCINT voltage inputs, which power the FPGA’s core logic.
The board uses three discrete regulators to generate the necessary voltages. However, various power supply vendors are developing integrated solutions specifically for Spartan-3 FPGAs.
Figure A-3 provides a detailed schematic of the various voltage regulators. Similarly, Figure A-6 shows the power decoupling capacitors
.Chapter 13
Expansion Connectors and Boards
Expansion Connectors
The Spartan-3 Starter Kit board has three 40-pin expansion connectors labeled A1, A2, and B1. The A1 and A2 connectors, indicated as @ and @, respectively, in Figure 1-2, are on the top edge of the board. Connector A1 is on the top left, and A2 is on the top right. The B1 connector, indicated as @ in Figure 1-2, is along the left edge of the board.
Figure 13-1: Spartan-3 Starter Kit Board Expansion Connectors
Table13-1 summarizes the capabilities of each expansion port. Port A1 supports a maximum of 32 user I/ O pins, while the other ports provide up to 34 user I/ O pins. Some pins are shared with other functions on the board, which may reduce the effective I/ O count for specific applications. For example, pins on the A1 port are shared with the SRAM address signals and the SRAM OE# and WE# control signals.
Table 13-1: Expansion Connector Features
Connector |
User I/O |
SRAM Address |
JTAG |
Serial Configuration |
Parallel Configuration |
A1 |
32 |
|
|
|
|
A2 |
34 |
|
|
|
|
B1 |
34 |
|
|
|
|
Each port offers some ability to program the FPGA on the Spartan-3 Starter Kit Board. For example, port A1 provides additional logic to drive the FPGA and Platform Flash JTAG chain. Similarly, ports A2 and B1 provide connections for Master or Slave Serial mode configuration. Finally, port B1 also offers Master or Slave Parallel configuration mode.
Each 40-pin expansion header, shown in Figure 13-2, uses 0.1-inch (100 mil) DIP spacing. Pin 1 on each connector is always GND. Similarly, pin 2 is always the +5V DC output from the switching power supply. Pin 3 is always the output from the +3.3V DC regulator.
UG130_c12_02_042504
Figure 13-2: 40-pin Expansion Connector
The pinout information for each connector appears below. The tables include the connections between the FPGA and the expansion connectors plus the signal names used in the detailed schematic in FigureA-1.
A1 Connector Pinout
The A1 expansion connector is located along the top edge of the board, on the left, as indicated by 0 in Figure 1-2. Table 13-2 provides the pinout for the A1 connector. The FPGA connections are specified in parentheses.
Table 13-2: Pinout for A1 Expansion Connector
Schematic Name |
FPGA Pin |
Connector |
FPGA Pin |
Schematic Name |
|
GND |
|
1 |
2 |
|
VU (+5V) |
Vcco (+3.3V) |
VCCO (all banks) |
3 |
4 |
(NB) |
ADR0 |
DB0 |
(N7) |
5 |
6 |
(L5) SRAM A0 |
ADR1 |
DB1 |
(TB) |
7 |
B |
(N3) SRAM A1 |
ADR2 |
DB2 |
(R6) |
9 |
10 |
(M4) SRAM A2 |
ADR3 |
DB3 |
(T5) |
11 |
12 |
(M3) SRAM A3 |
ADR4 |
DB4 |
(R5) |
13 |
14 |
(L4) SRAM A4 |
ADR5 |
DB5 |
(C2) |
15 |
16 |
(G3) SRAM WE# |
WE |
DB6 |
(C1) |
17 |
1B |
(K4) SRAM OE# |
OE |
Table 13-2: Pinout for A1 Expansion Connector (Continued)
Schematic Name |
FPGA Pin |
Connector |
FPGA Pin |
Schematic Name |
|
DB7 |
(B1) |
19 |
20 |
(P9) FPGA DOUT/ BUSY |
CSA |
LSBCLK |
(M7) |
21 |
22 |
(M10) |
MA1-DB0 |
MA1-DB1 |
(F3) SRAM A6 |
23 |
24 |
(G4) SRAM A5 |
MA1-DB2 |
MA1-DB3 |
(E3) SRAM A8 |
25 |
26 |
(F4) SRAM A7 |
MA1-DB4 |
MA1-DB5 |
(G5) SRAM A10 |
27 |
28 |
(E4) SRAM A9 |
MA1-DB6 |
MA1-DB7 |
(H4) SRAM A12 |
29 |
30 |
(H3) SRAM A11 |
MA1-ASTB |
MA1-DSTB |
(J3) SRAM A14 |
31 |
32 |
(J4) SRAM A13 |
MA1-WRITE |
MA1-WAIT |
(K5) SRAM A16 |
33 |
34 |
(K3) SRAM A15 |
MA1-RESET |
MA1-INT |
(L3) SRAM A17 |
35 |
36 |
jTAG Isolation |
jTAG Isolation |
TMS |
(C13) FPGA JTAG TMS |
37 |
38 |
(C14) FPGA JTAG TCK |
TCK |
TDO-ROM |
Platform Flash JTAG TDO |
39 |
40 |
Header J7, pin 3 |
TDO-A |
The A1 expansion connector shares connections with the 256Kx16 SRAM devices, specifically the SRAM address lines, and the OE# and WE# control signals. Similarly, the jTAG chain is available on pins 36 through 40. Pin 20 is the FPGA DOUT/ BUSY configuration signal and toggles during the FPGA configuration process.
A2 Connector Pinout
The A2 expansion connector is located along the top edge of the board, on the right, as indicated by @ in Figure 1-2. Figure 13-3 provides the pinout for the A2 connector. The FPGA connections are specified in parentheses.
Most of the A2 expansion connector pins connect only with the FPGA and are not shared. Pin 35 connects to the auxiliary clock socket, if an oscillator is installed in the socket. Pins 36 through 40 include the signals required to configure the FPGA in Master or Slave Serial mode.
Table 13-3: Pinout for A2 Expansion Connector
Schematic Name |
FPGA Pin |
Connector |
FPGA Pin |
Schematic Name |
|
GND |
|
1 |
2 |
|
VU (+5V) |
Vcco (+3.3V) |
VCC0 (all banks) |
3 |
4 |
(E6) |
PA-I01 |
PA-IO2 |
(D5) |
5 |
6 |
(C5) |
PA-I03 |
PA-IO4 |
(D6) |
7 |
B |
(C6) |
PA-I05 |
PA-IO6 |
(E7) |
9 |
10 |
(C7) |
PA-I07 |
PA-IOB |
(D7) |
11 |
12 |
(CB) |
PA-I09 |
PA-I010 |
(DB) |
13 |
14 |
(C9) |
PA-I011 |
PA-I012 |
(D10) |
15 |
16 |
(A3) |
PA-I013 |
PA-I014 |
(B4) |
17 |
1B |
(A4) |
PA-I015 |
PA-I016 |
(B5) |
19 |
20 |
(A5) |
PA-I017 |
PA-I01B |
(B6) |
21 |
22 |
(B7) |
MA2-DB0 |
MA2-DB1 |
(A7) |
23 |
24 |
(BB) |
MA2-DB2 |
MA2-DB3 |
(AB) |
25 |
26 |
(A9) |
MA2-DB4 |
MA2-DB5 |
(B10) |
27 |
2B |
(A10) |
MA2-DB6 |
MA2-DB7 |
(B11) |
29 |
30 |
(B12) |
MA2-ASTB |
MA2-DSTB |
(A12) |
31 |
32 |
(B13) |
MA2-WRITE |
MA2-WAIT |
(A13) |
33 |
34 |
(B14) |
MA2-RESET |
MA2-INT/ GCK4 |
(D9) Oscillator socket |
35 |
36 |
(B3) FPGA PR0G_B |
PROG-B |
DONE |
(R14) FPGA DONE |
37 |
3B |
(N9) FPGA INI T_B |
INIT |
CCLK |
(T15) FPGA CCLK Connects to (A14) via 390Q resistor |
39 |
40 |
(M11) |
DIN |
B1 Connector Pinout
The B1 expansion connector is located on the right edge of the board, as indicated by @ in Figure 1-2. Table 13-4 provides the pinout for the B1 connector. The FPGA connections are specified in parentheses.
Most of the B1 expansion connector pins connect only with the FPGA and are not shared. Pins 36 through 40 include the signals required to configure the FPGA in Master or Slave Serial mode. These same pins plus pins 5, 7, 9, 11, 13, 15, 17, 19, and 20 provide the signals required to configure the FPGA in Master or Slave Parallel mode.
Table 13-4: Pinout for B1 Expansion Connector
Schematic Name |
FPGA Pin |
Connector |
FPGA Pin |
Schematic Name |
|
GND |
|
1 |
2 |
|
VU (+5V) |
Vcco (+3.3V) |
VCCO (all banks) |
3 |
4 |
(C10) |
PB-ADR0 |
PB-DB0 |
(T3) FPGA RD_WR_B config |
5 |
6 |
(E10) |
PB-ADR1 |
PB-DB1 |
(N 11) FPGA D1 config |
7 |
8 |
(C11) |
PB-ADR2 |
PB-DB2 |
(P10) FPGA D2 config |
9 |
10 |
(D11) |
PB-ADR3 |
PB-DB3 |
(R10) FPGA D3 config |
11 |
12 |
(C12) |
PB-ADR4 |
PB-DB4 |
(T7) FPGA D4 config |
13 |
14 |
(D12) |
PB-ADR5 |
PB-DB5 |
(R7) FPGA D5 config |
15 |
16 |
(E11) |
PB-WE |
PB-DB6 |
(N6) FPGA D6 config |
17 |
18 |
(B16) |
PB-OE |
PB-DB7 |
(M6) FPGA D7 config |
19 |
20 |
(R3) FPGA CS_B config |
PB-CS |
PB-CLK |
(C15) |
21 |
22 |
(C16) |
MB1-DB0 |
MB1-DB1 |
(D15) |
23 |
24 |
(D16) |
MB1-DB2 |
MB1-DB3 |
(E15) |
25 |
26 |
(E16) |
MB1-DB4 |
MB1-DB5 |
(F15) |
27 |
28 |
(G15) |
MB1-DB6 |
MB1-DB7 |
(G16) |
29 |
30 |
(H15) |
MB1-ASTB |
MB1-DSTB |
(H16) |
31 |
32 |
(J16) |
MB1-WRITE |
MB1-WAIT |
(K16) |
33 |
34 |
(K15) |
MB1-RESET |
MB1-INT |
(L15) |
35 |
36 |
(B3) FPGA PROG_B |
PROG-B |
DONE |
(R14) FPGA DONE |
37 |
38 |
(N9) FPGA INI T_B |
INIT |
CCLK |
(T15) FPGA CCLK Connects to (A14) via 390Q resistor |
39 |
40 |
(M11) |
DIN |
Expansion Boards
Various expansion boards plug into the A1, A2, or B1 connectors as listed below:
Spartan-3 Starter Kit Expansion Boards http:/ /www.xilinx.com/s3boards
Digilent Expansion Boards
https:/ / digilent.us/Sales/boards.cfm#Peripheral
Digilent Breakout Probe Header (TPH1)
https:/ / digilent.us/Sales/Product.cfm?Prod=TPH1
Digilent Breadboard (DBB1)
https:/ / digilent.us/Sales/Product.cfm?Prod=DBB1
Digilent Wi re-w rap Board (D WR1)
https:/ / digilent.us/Sales/Product.cfm?Prod=DWR1
Digilent SPP, EPP, ECP Parallel Port (PI01) https:/ / digilent.us/Sales/Product.cfm?Prod=PI0
1Appendix A
Board Schematics
This appendix provides the schematics for the Spartan-3 Starter Kit Board:
Figure A-1, “A1, A2, and B1 Expansion Connectors"
Figure A-2, “Slide Switches, Push Buttons, LEDs, and Four-Character 7-Segment
Display"
Figure A-3, “Voltage Regulators, JP2 Jumper Setting for PS/2 Port Voltage"
Figure A-4, “FPGA Configuration Interface, Platform Flash, JTAG Connections,
Jumper JP1"
Figure A-5, “FPGA I/O Connections, Clock Sources"
Figure A-6, “Power Decoupling Capacitors"
FigureA-7, “RS-232 Serial Port, VGA Port, PS/ 2 Port, Parallel Cable IV JTAG Interface"
FigureA-B, “2x256Kx16 Fast Asynchronous SRAM Interface"
FigureA-9, “Digilent JTAG3 Low-Cost JTAG Download/ Debug Cable
"
UG130_ApA_01_042604
Figure A-1: A1, A2, and B1 Expansion Connector
s
u ~
feS
o S, CD-
CO sj
c
CD
a °
UG130_ApA_02_042604
Figure A-2: Slide Switches, Push Buttons, LEDs, and Four-Character 7-Segment Display
UG130_ApA_03_042604
Figure A-3: Voltage Regulators, JP2 Jumper Setting for PS/2 Port Voltag
eHXILINX
UG130_ApA_04_042604
Figure A-4: FPGA Configuration Interface, Platform Flash, JTAG Connections, Jumper JP
1
Figure A-5: FPGA I/O Connections, Clock Sources
HXILINX
UG130_ApA_06_042604
Figure A-6: Power Decoupling Capacitors
UG130_ApA_07_042604
Figure A-7: RS-232 Serial Port, VGA Port, PS/2 Port, Parallel Cable IV JTAG Interface
HXILINX
UG130_ApA_08_042604
Figure A-8: 2x256Kx16 Fast Asynchronous SRAM Interface
UG130_ApA_09_042604
Figure A-9: Digilent JTAG3 Low-Cost JTAG Download/Debug Cabl
eAppendix B
Reference Material for Major Components
Table B-1 lists the major components on the Spartan-3 Starter Kit Board, including full part numbers and links to complete device data sheets.
Table B-1: Major Components and Data Sheet Links
Device |
Vendor |
Part Number |
Description/Data Sheet Link |
o |
Xilinx, Inc. |
XC3S200-4FT256C |
Spartan-3 FPGA http:/ / www.xilinx.com/ bvdocs/publications/ ds099.pdf |
© |
Xilinx, Inc. |
XCF02SVO20C |
Platform Flash Configuration Flash PROM http:/ / www.xilinx.com/ bvdocs/publications/ ds123.pdf |
© |
Integrated Silicon Solutions, Inc. (ISSI) |
IS61LV25616AL-10T |
256Kx16 Fast Asynchronous SRAM http:/ /www.issi.com/ pdf/ 61LV25616AL.pdf |
© |
Maxim |
MAX3232 |
Dual-Channel RS-232 Voltage Translator http:/ / pdfserv.maxim-ic.com/ en/ ds/ MAX3222-MAX3241.pdf |
© |
Epson |
SG-8002JF |
50 MHz Crystal Oscillator http:/ /www.knap.at/ de/ pdf/ kat o/ sg8002jf.pdf |
© |
Interex |
APA-101M-05 |
5V Switching Regulator |
© |
National Semiconductor |
LM1086CS-ADJ |
3.3V Regulator http://www.national.com/ pf/ LM/ LM1086.html#Datasheet |
© |
STMicroelectronics |
LF25CDT |
2.5V Regulator http:/ /www.st.com/ stonline/ books/ pdf/ docs/2574.pdf |
© |
? |
|
1.2V Regulator |
