Добавил:
Upload Опубликованный материал нарушает ваши авторские права? Сообщите нам.
Вуз: Предмет: Файл:
Пособие.Основы роторного бурения.Пенькова.Макси...doc
Скачиваний:
0
Добавлен:
01.03.2025
Размер:
16 Мб
Скачать
☆

Glossary

A

abandoned well

a well no longer in use, whether dry, inoperable or no longer productive, and the previous operator has intentionally relinquished its interest in the well.

abrasion

wearing away by friction

air drilling

a method of rotary drilling that uses compressed air as the circulation medium. Compressed air removes the cuttings with equal or greater efficiency. The rate of penetration is usually increased considerably when air drilling is used. However, a principal problem in air drilling is the penetration of formations containing water, since the entry of water into the system reduces the ability of the air to remove the cuttings.

annular space

(annulus)

the space around a pipe in a wellbore, the outer wall of which may be the wall of either the borehole or the casing

associated reservoir

oil and gas reservoir with a gas cap. Gas production from these reservoirs is generally restricted in order to preserve the gas cap energy thereby increasing ultimate recovery.

B

ball up

to collect a mass of sticky consolidated material, usually drill cuttings, on drill pipe, drill col­lars, bits, and so forth. A bit with such material attached to it is termed a balled-up bit. Balling up is frequently the result of inadequate pump pressure or insufficient drilling fluid.

bearing

an object, surface, or point that sup­ports; a machine part in which another part (such as a journal or pin) turns or slides.

bit

the cutting or boring element used in drilling oil and gas wells. The bit consists of a cutting element and a circulating element. The circulating element permits the passage of drilling fluid and utilizes the hydraulic force of the fluid stream to improve drilling rates. In rotary drilling, several drill collars are joined to the bottom end of the drill pipe column, and the bit is attached to the end of the string of drill collars. Most bits used in rotary drilling are roller cone bits, but diamond bits are also used extensively.

bit hydraulic horsepower (bhhp)

the measure of hydraulic power expended through the bit nozzles for cleaning the bit cutters and the hole bottom.

bit program

a plan for the expected number and types of bits that are to be used in the drilling of a well. The bit program takes into account all the fac­tors that affect bit performance so that reliable cost calculations can be made.

blooey line

the discharge pipe from a well being drilled by air drilling. The blooey line is used to con­duct the air or gas used for circulation away from the rig to reduce the fire hazard as well as to transport the cuttings a suitable distance from the well.

bottomhole

the lowest or deepest part of a well.

C

caving

collapsing of the walls of the wellbore; also called sloughing.

chip hold-down effect

the holding of formation rock chips in place as a result of high differential pressure in the wellbore. This effect limits the cutting action of the bit by retarding circulation of bit cuttings out of the hole.

clear water drilling

drilling operations in which water is used as the circulating fluid.

compressive strength

the degree of resistance of a material to a force acting along one of its axes in a manner tending to collapse it; usually expressed in pounds of force per square inch (psi) of surface affected or in kilopascals.

cone offset

the amount by which lines drawn through the center of each cone of the bit fail to meet in the center of the bit. For example, in a roller cone bit with three cones, three lines can be drawn through the center of each cone and extended to the center of the bit. If these cone centerlines do not meet in the bit's center, the cones are said to be offset.

crown block

an assembly of sheaves, mounted on beams at the top of the derrick, over which the drilling line is reeved.

cutters

cutting teeth on the cones of a roller cone bit.

cuttings

the fragments of rock dislodged by the bit and brought to the surface in the drilling mud. They are not the same as cavings, which are particles that fall off the wall of the hole. Washed and dried samples of the cuttings are analyzed by geologists to obtain information about the formations drilled.

D

density

the mass or weight of a substance per unit volume. For instance, the density of a drilling mud may be 10 pounds per gallon (ppg), 74.8 pounds per cubic foot (lb/ft3), or 1 198.2 kilograms per cubic metre (kg/m3).

desander

a centrifugal device for removing sand from drilling fluid to prevent abrasion of the pumps. It may be operated mechanically or by a fast-moving stream of fluid inside a special cone-shaped vessel, in which case it is sometimes called a hydrocy clone.

desilter

a centrifugal device for removing very fine particles, or silt, from drilling fluid to keep the amounts of solids in the fluid at the lowest possible point. Usually, the lower the solids content of mud, the faster is the rate of penetration. The desilter works on the same principle as a desander.

diamond bit

a drilling bit that has a steel body sur­faced with a matrix and industrial diamonds. Cutting is performed by the rotation of the very hard diamonds over the rock surface.

differential pressure

the difference between two fluid pressures; for example, the difference between the pressure in a reservoir and in a wellbore drilled in the reservoir, or between atmospheric pressure at sea level and at 10,000 feet. Also called pressure differen­tial.

discharge line

a line through which drilling mud travels from the mud pump to the standpipe on its way to the wellbore.

dogleg

a short change of direction in the wellbore, frequently resulting in the formation of a key seat.

drag bit

any of a variety of drilling bits with no moving parts that drill by intrusion and drag.

drill collar

a heavy, thick-walled tube, usually steel, used between the drill pipe and the bit in the drill stem to provide a pendulum effect to the drill stem and weight to the bit.

drilling fluid

circulating fluid, one function of which is to force cuttings out of the wellbore and to the surface. Other functions are to cool the bit and to counteract downhole formation pressure. While a mixture of barite, clay, water, and chemical additives is the most common drilling fluid, wells can also be drilled by using air, gas, water, or oil-base mud as the drilling fluid.

drill-off test

a method of determining optimum weight on bit and overall bit performance by tying down the brake and measuring the time required to "drill off certain weight intervals as the drill stem decompresses.

drill stem

all members in the assembly used for rotary drilling from the swivel to the bit, including the kelly, drill pipe and tool joints, drill collars, stabilizers, and various specialty items.

drill string

the column, or string, of drill pipe with attached tool joints that transmits fluid and rotational power from the kelly to the drill collars and bit. Often, especially in the oil patch, the term is loosely applied to both drill pipe and drill collars.

E

electric well log

a record of certain electrical characteristics of formations traversed by the borehole, made to identify the formations, determine the nature and amount of fluids they contain, and estimate their depth. Also called an electric log or electric survey.

Enhanced Oil Recovery (EOR)

the use of any process for the displacement of oil from the reservoir other than primary recovery.

exploratory well

any well drilled for the purpose of securing geological or geophysical information to be used in the exploration or development of oil, gas, geothermal, or other mineral resources, except coal and uranium, and includes what is commonly referred to in the industry as "slim hole tests," "core hole tests," or "seismic holes".

extraction loss

the reduction in volume and energy content of natural gas resulting from the removal of natural gas liquid constituents.

F

filtration loss

the escape of the liquid part of a drilling mud into permeable formations.

fishtail bit

a drilling bit with cutting edges of hard alloys; also called a drag bit. First used when the rotary system of drilling was developed about 1900, it is still useful in drilling very soft formations.

formation fluid

fluid (such as gas, oil, or water) that exists in a subsurface rock formation.

G

gauge

the diameter of a bit or the hole drilled by the bit.

gauge cutters

the teeth or tungsten carbide inserts in the outermost row on the cones of a bit, so called because they cut the outside edge of the hole and determine the hole's gauge or size. Also called heel teeth.

gel strength

a measure of the ability of a colloidal dispersion to develop and retain a gel form, based on its resistance to shear. The gel strength, or shear strength, of a drilling mud determines its ability to hold solids in suspension. Sometimes bentonite and other colloidal clays are added to drilling fluid to increase its gel strength.

gpm

gallons per minute.

gravity

the attraction exerted by the earth's mass on objects at its surface; the weight of a body.

H

hardfacing

an extremely hard material, usually crushed tungsten carbide, that is applied to the out­side surfaces of tool joints, drill collars, stabilizers, and other rotary drilling tools to minimize wear when they are in contact with the wall of the hole.

hydraulic horsepower (hhp)

a measure of the power of a fluid under pressure.

hydraulics

1. the branch of science that deals with practical applications of water or other liquid in motion.

2. the planning and operation of a rig hydraulics program, coordinating the power of the circulating fluid at the bit with other aspects of the drilling program so that bottomhole cleaning is max­imized.

hydrostatic pressure

the force exerted by a body of fluid at rest; it increases directly with the density and the depth of the fluid and is expressed in psi or kPa. The hydrostatic pressure of fresh water is 0.433 psi per foot of depth (9.792 kPa/m). In drilling, the term refers to the pressure exerted by the drilling fluid in the wellbore. In a water-drive field, the term refers to the pressure that may furnish the primary energy for production.

I

insert

a cylindrical object, rounded or chisel-shaped on one end and usually made of tungsten car­bide, that is inserted in the cones of a bit, the cutters of a reamer, or the blades of a stabilizer to form the cutting element of the bit or the reamer or the wear surface of the stabilizer. Also called a compact.

J

junk

metal debris lost in a hole. Junk may be a lost bit, pieces of a bit, milled pieces of pipe, wrenches, or any relatively small object that impedes drilling and must be fished out of the hole.

K

kelly

the heavy steel member, three-, four-, six-, or eight-sided, suspended from the swivel through the rotary table and connected to the topmost joint of drill pipe to turn the drill stem as the rotary table turns. It has a bored passageway that permits fluid to be cir­culated into the drill stem and up the annulus, or vice versa.

kick

an entry of water, gas, oil, or other formation fluid into the wellbore during drilling. It occurs because the pressure exerted by the column of drilling fluid is not great enough to overcome the pressure exerted by the fluids in the formation drilled. If pro­mpt action is not taken to control the kick or kill the well, a blowout may occur.

L

liquefied natural gas (LNG)

natural gas that has been converted to liquid form for ease of storage or transport. Liquefied natural gas takes up about 1/600th the volume of natural gas at a stove burner tip. It is odorless, colorless, non-corrosive, and non-toxic.

M

make a trip

to hoist the drill stem out of the wellbore to perform one of a number of operations such as changing bits, taking a core, and so forth, and then to return the drill stem to the wellbore.

marl

a semisolid or unconsolidated clay, silt, or sand.

matrix

the material in which the diamonds on a dia­mond bit are set.

mud

the liquid circulated through the wellbore dur­ing rotary drilling and workover operations. In addi­tion to its function of bringing cuttings to the surface, drilling mud cools and lubricates the bit and drill stem, protects against blowouts by holding back subsurface pressures, and deposits a mud cake on the wall of the borehole to prevent loss of fluids to the formation. Although it was originally a suspension of earth solids (especially clays) in water, the mud used in modern drilling operations is a more complex, three-phase mixture of liquids, reactive solids, and inert solids. The liquid phase may be fresh water, diesel oil, or crude oil and may contain one or more conditioners.

mud cake

the sheath of mud solids that forms on the wall of the hole when liquid from mud filters into the formation; also called wall cake or filter cake.

N

nozzle

a passageway through jet bits that allows the drilling fluid to reach the bottom of the hole and flush the cuttings through the annulus. Nozzles come in different sizes that can be interchanged on the bit to allow more or less flow.

O

oil-base mud

an oil that contains from less than 2 percent up to 5 percent water. The water is spread out, or dispersed, in the oil as small droplets.

oil-emulsion mud

a water-base mud in which water is the continuous phase and oil is the dispersed phase. The oil is spread out, or dispersed, in the water in small droplets, which are tightly emulsified so that they do not settle out. Because of its lubricating abilities, an oil-emulsion mud increases the drilling rate and ensures better hole conditions than other muds.

oil mud

a drilling mud in which oil is the continuous phase. Oil-base mud and invert-emulsion mud are types of oil muds. They are useful in drilling certain formations that may be difficult or costly to drill with water-base mud.

optimization

the manner of planning and drilling a well so that the most usable hole will be drilled for the least money.

overburden

the strata of rock that lie above the stratum of interest, in drilling.

P

PCD

polycrystalline diamond.

pore

an opening or space within a rock or mass of rocks, usually small and often filled with some fluid (water, oil, gas, or all three).

porous

having pores, or tiny openings, as in rock.

porosity

the condition of something that contains pores (such as rock formation).

ppg

pounds per gallon.

psi

pounds per square inch.

pump liner

a cylindrical, accurately machined, metallic section that forms the working barrel of some reciprocating pumps. Liners are an inexpensive means of replacing worn cylinder surfaces, and in some pumps they provide a method of conveniently changing the displacement and capacity of the

R

rate of penetration (ROP)

a measure of the speed at which the bit drills into formations, usually expressed in feet (metres) per hour or minutes per foot (metre).

relative density

the ratio of the mass of a given volume of a substance to the mass of a like volume of a standard substance, such as water or air. In conven­tional measurement units, specific gravity is similar to relative density.

relative permeability

a measure of the ability of two or more fluids (such as water, gas, and oil) to flow through a rock formation when the formation is to­tally filled with several fluids. The permeability measure of a rock filled with two or more fluids is dif­ferent from the permeability measure of the same rock filled with only a single fluid.

roller cone bit (rock bit)

a drilling bit made of two, three, or four cones, or cutters, that are mounted on extremely rugged bearings. Also called rock bits. The surface of each cone is made up of rows of steel teeth or rows of tungsten carbide inserts.

rotary

the machine used to impart rotational power to the drill stem while permitting vertical movement of the pipe for rotary drilling. Modern rotary machines have a special component, the rotary bushing, to turn the kelly bushing, which permits ver­tical movement of the kelly while the stem is turning.

rotary hose

a reinforced flexible tube on a rotary drilling rig that conducts the drilling fluid from the mud pump and standpipe to the swivel and kelly; also called the mud hose or the kelly hose.

rotary speed

the speed, measured in rpm, at which the rotary table is operated.

rotating head

a sealing device used to close off the annular space around the kelly in drilling with pressure at the surface, usually installed above the main blowout preventers. A rotating head makes it possible to drill ahead even when there is pressure in the annulus that the weight of the drilling fluid is not overcoming; the head prevents the well from blowing out. It is used mainly in the drilling of formations that have low permeability. The rate of penetration through such formations is usually rapid.

rpm

revolutions per minute

S

shale

a fine-grained sedimentary rock composed of consolidated silt and clay or mud. Shale is the most frequently occurring sedimentary rock.

shear

action or stress that results from applied forces and that causes or tends to cause two adjoining parts of a body to slide relative to each other in a direction parallel to their plane of contact.

silicon tetrafluoride

a gas that can be readily absorbed by water and that is used to seal off water­bearing formations in air drilling.

slack off

to lower a load or ease up on a line. A driller will slack off to put additional weight, on the bit.

spurt loss

the initial loss of drilling mud solids by filtration, making formations easier to drill.

standpipe

a vertical pipe rising along the side of the derrick or mast, which joins the discharge line leading from the mud pump to the rotary hose and through which mud is pumped going into the hole.

steel-tooth bit

a roller cone bit in which the surface of each cone is made up of rows of steel teeth. Also called a milled-tooth bit or milled bit.

strata

distinct, usually parallel beds of rock. An individual bed is a stratum.

stringer

a relatively narrow splinter of a rock formation that is stratigraphically disjoint, interrupting the consistency of another formation and making drilling that forma­tion less predictable. A shale formation, for example, may be broken by a stringer of sandstone.

swivel

a rotary tool that is hung from the rotary hook and traveling block to suspend and permit free rotation of the drill stem. It also provides a connection for the rotary hose and a passageway for the flow of drilling fluid into the drill stem.

T

torque

the turning force that is applied to a shaft or other rotary mechanism to cause it to rotate or tend to do so. Torque is measured in units of length and force (foot-pounds, newton-metres).

traveling block

an arrangement of pulleys, or sheaves, through which drilling line is reeved and which moves up and down in the derrick or mast.

tricone bit

a type of bit in which three cone-shaped cutting devices are mounted in such a way that they intermesh and rotate together as the bit drills. The bit body may be fitted with nozzles, or jets, through which the drilling fluid is discharged. A one-eyed bit is used in soft formations to drill a deviated hole.

tripping

the operation of hoisting the drill stem out of and returning it to the wellbore; making a trip.

twistoff

a complete break in pipe caused by rota­tional force wrenching damaged pipe apart.

U

unconsolidated formation

a loosely arranged, apparently unstratified section of rock.

undergauge bit

a bit whose outside diameter is worn to the point at which it is smaller than it was when new. A hole drilled with an undergauge bit is said to be undergauge.

V

viscosity

a measure of the resistance of a liquid to flow. Resistance is brought about by the internal fric­tion resulting from the combined effects of cohesion and adhesion. The viscosity of petroleum products is commonly expressed in terms of the time required for a specific volume of the liquid to flow through an orifice of a specific size.

vug

a cavity in a rock.

W

wall cake

also called filter cake or mud cake.

water-base mud

a drilling mud in which the continuous phase is water. In water-base muds, any add­itives are dispersed in the water.

watercourse

a hole inside a bit through which drill­ing fluid from the drill stem is directed.

wellbore

a borehole; the hole drilled by the bit. A wellbore may have casing in it or it may be open (uncased); or a portion of it may be cased, and a por­tion of it may be open. Also called borehole or hole.

wildcat

a well drilled in an area where no oil or gas production exists for the purpose of discovering a new field or reservoir. With present-day exploration methods and equipment, about one wildcat out of every nine proves to be productive, although not necessarily profitable.