Добавил:
Upload Опубликованный материал нарушает ваши авторские права? Сообщите нам.
Вуз: Предмет: Файл:
Honda_CB500_S_93-01_Haynes_Service_Manual_ENG_Skanirovanny.doc
Скачиваний:
7
Добавлен:
01.07.2025
Размер:
12 Мб
Скачать
☆

20.3A Upper crankcase 6 rnm bolts (a), 8 mm bolts (b) and 10 mm (c) bolt

pattern, until they are finger-tight, then remove them (see illustration). Note: As each bolt is removed, store it in its relative position in a cardboard template of the crankcase halves. This will ensure all bolts are installed in their correct locations on reassembly.

  1. Unscrew the twelve 8 mm lower crankcase (crankshaft and balancer shaft journals) bolts (see illustration 20.7). Unscrew the bolts evenly, a little at a time in a criss-cross pattern until they are finger-tight, then remove them, along with the washers and place them in the template. Discard the washers as new ones should be fitted on reassembly.

  2. Carefully lift the lower crankcase half off the upper half, using a soft-faced hammer to tap around the joint to initially separate the halves if necessary. Note: If the halves do not

20.3B Triangle (arrowed) denotes use of sealing washer on adjacent bolt

separate easily, make sure all fasteners have been removed. Do not try and separate the halves by levering against the crankcase mating surfaces as they are easily scored and will leak oil on reassembly. The lower crankcase half will come away with the gearchange mechanism external components (if not already removed) and the selector drum and forks, leaving the crankshaft and transmission shafts in the upper crankcase half. The lower main bearing shells and the lower balancer shaft bearing shells should also come away with the lower crankcase half. Remove them if they are loose, noting their locations (see Sections 25 and 26).

  1. If required, remove the three locating dowels from the crankcase if they are loose (they could be in either crankcase half), noting their locations (see illustration). Similarly remove the two oil nozzles, noting which way up they fit.

  2. Refer to Sections 21 to 30 for the removal, inspection and installation of the components housed within the crankcases.

Reassembly

  1. Remove all traces of sealant from the crankcase mating surfaces.

  2. Ensure that all components and their bearings are in place in the upper and lower crankcase halves. If the transmission shafts have not been removed, check the condition of the output shaft oil seal on the left-hand end of the shaft and renew it if it is damaged or deteriorated (see Section 28); it is sound practice to renew this seal anyway. Apply

20.7 Lower crankcase 6 mm bolts (A) and 8 mm bolts (B)

20.10 Locating dowels (A) and oil nozzles (B)

Engine, clutch and transmission 2*35

20.13 Renew the oil seal (arrowed) if it is worn or shows signs of leaking

20.16 Apply sealant to the lower crankcase half where illustrated

20.17 Carefully lower the lower crankcase half onto the upper crankcase half

some grease to the inside of the new seal on installation (see illustration).

  1. Generously lubricate the crankshaft and transmission shafts, particularly around the bearings, with clean engine oil, then use a rag soaked in high flash-point solvent to wipe over the mating surfaces of both crankcase halves to remove all traces of oil.

  2. If removed, install the three locating dowels and the two oil nozzles in the upper crankcase half (see illustration 20.10). The oil nozzles must be fitted with the wider aperture facing out, ie towards the crankcase lower half.

  3. Apply a small amount of suitable sealant to the outer mating surface of the lower crankcase half (see illustration).

Caution: Do not apply an excessive amount of sealant as it will ooze out when the case halves are assembled and may obstruct oil passages. Do not apply the sealant on or too close to any of the bearing inserts or surfaces.

17 Check again that all components are in position, particularly that the bearing shells are still correctly located in the lower crankcase half and that the camchain guides are correctly located in the upper crankcase half. Carefully install the lower crankcase half down onto the upper crankcase half, making sure each gear selector fork locates correctly in the groove in its pinion, that the guide pins on the forks locate correctly in the grooves in

the selector drum and that the crankcase dowels all locate correctly into the lower crankcase half (see illustration).

  1. Check that the lower crankcase half is correctly seated. Note: The crankcase halves should fit together without being forced. If the casings are not correctly seated, remove the lower crankcase half and investigate the problem. Do not attempt to pull them together using the crankcase bolts as the casing will crack and be ruined.

  2. Clean the threads of the twelve 8 mm lower crankcase (crankshaft and balancer shaft journals) bolts. Apply clean engine oil to the threads and seating surfaces of the bolts and install them with new washers in their original locations (see illustration). Secure all bolts finger-tight at first, then tighten them evenly and a little at a time in a criss-cross pattern, starting from the centre and working outwards, to the torque setting specified at the beginning of this Chapter.

  3. Clean the threads of the eight 6 mm lower crankcase bolts and insert them in their original locations. Secure all bolts finger-tight at first, then tighten them evenly a little at a time in a criss-cross pattern to the torque setting specified at the beginning of this Chapter (see illustration).

  4. Turn the engine over. Ensure the camchain is secured to prevent it dropping into the crankcase. Clean the threads of the single 10 mm upper crankcase bolt and insert

it into the rear left-hand corner of the crankcase. Tighten the bolt to the specified torque (see illustration).

  1. Clean the threads of the two 8 mm upper crankcase bolts and insert them in their original locations with new sealing washers. Secure the bolts finger-tight at first, then tighten them evenly a little at a time to the torque setting specified at the beginning of this Chapter (see illustration).

  2. Clean the threads of the five 6 mm upper crankcase bolts and insert them in their original locations. Fit new sealing washers where the bolt locations are identified by a triangle cast into the crankcase. Secure the bolts finger-tight at first, then tighten them evenly a little at a time in a criss­cross pattern to the torque setting specified at

Соседние файлы в предмете [НЕСОРТИРОВАННОЕ]