Добавил:
Upload Опубликованный материал нарушает ваши авторские права? Сообщите нам.
Вуз: Предмет: Файл:
Honda_CB500_S_93-01_Haynes_Service_Manual_ENG_Skanirovanny.doc
Скачиваний:
7
Добавлен:
01.07.2025
Размер:
12 Мб
Скачать
☆

22.2 Measuring big-end side clearance

Dirt or foreign particles trapped behind a bearing insert result in high spots on the bearing which lead to failure. 8 To avoid bearing problems, clean all parts thoroughly before reassembly, double check all bearing clearance measurements and lubricate the new bearings with clean engine oil during installation.

I

22 Connecting rods and bearings - removal, inspection and installation

Note: To remove the connecting rods, the engine must be removed from the frame.

Removal

  1. 22.3 Mark the connecting rods and big-end caps with the cylinder number

    Remove the engine from the frame (see Section 5). Remove the cylinder head (see Section 10), and separate the crankcase halves (see Section 20). Note: Once the cylinder head has been removed, rest the engine upside-down on a block of wood to avoid damaging the camchain and camchain guides, and to provide sufficient clearance for the pistons and connecting rods to be withdrawn from the cylinders.

  2. Before removing the rods from the crankshaft, measure the big-end side clearance with a feeler gauge (see illustration). If the clearance on any rod is greater than the service limit listed in this Chapter's Specifications, renew that rod.

  3. Using paint or a felt marker pen, mark the cylinder identity on each piston, connecting rod and cap. Mark across the cap-to-connecting rod join and note which side of the rod faces the front of the engine to ensure that the cap and rod are fitted the correct way around on reassembly. The oil hole in the big-end of each connecting rod should face the back (inlet side) of the engine. Note: The number already across the rod and cap indicates rod size, not cylinder number (see illustration).

  4. Unscrew the big-end cap nuts and separate the caps, complete with the lower bearing

Engine, clutch and transmission 2»37

22.4 Detach the big-end caps with the lower bearing shells (arrowed)

shells, from the crankpins (see illustration), then detach the connecting rods, complete with the upper bearing shells, from the crankpins.

5 Ensure the camchain is free to be lifted out of the engine and lift the crankshaft with the camchain attached out of the upper crankcase half, taking care not to dislodge the main bearing shells. Push each piston/connecting rod assembly down the cylinder and remove it, making sure the connecting rod does not mark the cylinder bore (see illustration). To ease withdrawal of the piston/connecting rod assembly, remove any ridge of carbon built up on the top of each cylinder bore. If there is a pronounced wear ridge, remove it using a ridge reamer. Caution: Do not try to remove the piston/connecting rod assemblies from the bottom of the cylinder bore. The piston will

22.5A Remove the piston and connecting rod from the top end of the cylinder

nof pass the crankcase main bearing webs. If the piston is pulled right to the bottom of the bore the oil control ring will expand and lock the piston in position. If this happens it is likely the ring will be broken. Install the relevant bearing shells (if removed), bearing cap and nuts on each connecting rod assembly so that they are all kept together as a matched set (see illustration). 6 Do not remove the bolts from the connecting rods. Note: It is not necessary to renew the big-end bolts when the connecting rods are removed. If, for any reason, the bolts have to be renewed, drive the old bolts out of the rods by tapping gently with a hammer. Under no circumstances twist the bolts while they are in the rods. Because the bolts have knurled shanks and are a tight fit in the rods, take care to align the bolt heads with the machined insets in the rod shoulders before

Соседние файлы в предмете [НЕСОРТИРОВАННОЕ]