- •1 Level (6 points)
- •History of the need for building materials
- •Cement production in the Republic of Kazakhstan
- •The history of obtaining and production cement
- •Economics of cement production
- •Determination of clinker, cement and additives introduced in the grinding
- •The composition of the raw meal. Equations 1-4
- •The composition of the raw meal. Equations 5-9
- •An overview of phase composition and quality phase of clinker
- •Portland cement clinker.
- •Chemical and mineralogical composition alite
- •Chemical and mineralogical composition of belite
- •Phase aluminate
- •Phase Ferrite
- •Other clinker phases
- •The composition and place of origin of the phases in portland cement clinker
- •Analysis of the raw meal, cement and clinker
- •Microscopic research of clinker
- •Recent developments in the use of X-rays
- •Petrographic analysis of clinker
- •Cement production
- •Raw materials and fuels in cement production
- •The raw materials of cement industry
- •Limestone and clay
- •A natural mixture of clay and limestone
- •Waste and their use in the cement industry
- •2 Level (6 points)
- •Mining, processing of raw materials, grinding of raw meal and homogenisation.
- •The blending warehouse of raw materials and its functions.
- •Development of the pile by rotary excavator
- •The process of burning cement clinker. General concepts
- •Chemical reactions during heat treatment of portland cement raw meal (main reaction clinker burning)
- •The dehydration of kaolinite
- •The reactions during the sintering
- •Reaction with cooling
- •Homogeneity of the raw meal
- •The process of burning cement clinker
- •Procedures for burning cement clinker
- •Decarbonizators with upward vertical gas flue.
- •The fuel in cement production
- •Clinker cooler
- •Cooler sf (Smidth-Fuller).
- •Storage of clinker
- •Cement Grinding
- •Milling equipment
- •The fineness of grinding and particle size distribution (grain) composition of the cement
- •Storage, packing, shipment cement to the consumer
- •The granulated blast furnace slag (s)
- •Pozzolan (p, q)
- •Natural pozzolanic additives (р)
- •Natural volcanic pozzolanic additives (q)
- •3 Level (8 points)
- •Fly ash rich in silica (V)
- •Lime ash dust (w)
- •Calcined shale (t)
- •Limestone (l, ll)
- •The quartz dust (d)
- •Small components
- •Calcium sulphate
- •The cement admixture
- •Cement according to standard
- •Physical and chemical properties of cements according to European standard
- •Cements with special properties
- •Well cement
- •Hydration
- •The reaction of silicates (c3s, c2s)
- •Hydration c3s
- •Hydration c2s
- •Reactions of hydration aluminate without participation of sulfates
- •Reactions hydration aluminate with participation sulphates
- •Hydration ferrite (c4af)
- •Taylor Model
- •Model Stark
- •The cement hydration
- •Reaction of the secondary components
- •Hydration of cement containing granulated slag
- •Reactions pozzolanic materials
- •4 Level (8 points)
- •Slowing solidification
- •Structure of a cement stone
- •Building lime
- •The historical and economic situation. Raw material deposits
- •Production and processing of limestone
- •Burning lime
- •Shaft kiln to coke (coal) and gas fuel
- •The rotary tube kiln
- •Counter current regenerative kiln (ggr-kiln)
- •Shaft ring kiln
- •Grinding and shipment of burnt lime
- •Slaked lime
- •The use of lime products
- •The requirements of stst 9179-79 to building lime
- •Gypsum. History and economy
- •Physical and chemical bases of gypsum binders
- •Phases in the system CaSo4 - h2o
- •The crystal structures, double salts, mixed crystals
- •Natural gypsum, natural anhydrite
- •The chemical gypsum
- •Uddg- gypsum
- •Production of calcium sulphate binders
- •Technological processes in the production of calcium sulphate binders
- •Autoclave method for producing α-hemihydrate
- •Gypsum boiling kettle for the production of ß-hemihydrate
- •5 Level (12 points)
- •The high temperature burning of gypsum method (multiphase gypsum) on the grate
- •Properties capable of hardening calcium sulphates
- •Hydration CaSo4-binding
- •Natural -, uusdg - and chemical anhydrite
- •The properties of the treated gypsum building materials
- •Other areas of application
- •The norms, chemical analysis and phase analysis
- •Gypsum Products
- •The requirements of gost 125-79 for the quality of construction gypsum
- •Other inorganic binding materials
- •Alumina cement
- •Production of alumina cement
- •Chemical and mineralogical composition of the alumina cement
- •Areas of use alumina cement
- •Softeners (plasticizers), added during the production concrete
- •Softeners (plasticizers), added to the concrete mix
- •Concrete
- •Mobile concrete plants
- •Concrete for precast concrete elements
- •Self-compacting concrete
- •Building mortar
- •Cement mortar
- •Plaster
- •Cementing deep wells
The rotary tube kiln
Structurally, the tubular furnace (. Fig 97) is riveted or welded sheet steel drum thickness of 20 - 70 mm, mounted on roller bearings angle 2 - 50 to the horizontal plane. To stiffen the drum along its length are welded several shells that are thicker than the shell itself. Inside the drum is lined with refractory brick. Sometimes, to increase the residence time in the furnace, the maximum temperature zone of the drum expanding. With the ends adjacent to the furnace so-called head, which usually make sliding. Appointment of the top of the head - removal of gases and dust removal chastichnoeih. A body of this head pipe passes to load the oven. The lower fuel-head set apparatus and a receiving bin, into which the finished product is discharged from the furnace.
Fig. 97. The tubular rotary kiln 1 - fuel burning device; 2 - lower head; 3 - shoe; 4 - shell is; 5 - Drum Corps; 6 - lining; 7 - loading chute; 8 - upper head; 9- bandage; 10 - the driving gear; 11 - ring gear; 12 - roller carriage
The most critical part of the installation are supporting devices (bandages, and rollers), whose purpose - to take the load and ensure smooth rotation of the furnace. The load from the drum on the rollers is transferred via shrouds. For small diameter tires are mounted on the drum by hot landing. The drums of large diameter in order to prevent axial displacement of their tires mounted on cast iron shoes with heads rotated in different directions (Fig. 98). Make bandages from cast steel grades 35HGSA, 2HGSL, ZOGSL.
Fig. 98. Planting rectangular band on the stove body: 1 - regulating lining; 2 - band; 3 - steel shoe; 4 - shell is
Fig. 99. Methods for fixing the ring gear: 1 - drum; 2 - a nave; 3 - ring gear; 4 - longitudinal spring; 5 - steel segment; 6 - Joint; 7 - leaf spring
Tubular small size rotary kilns have two legs, and furnaces of great length do multisupport. Span take up to 20 m.
The diameter of the rollers is 0.25 - 0.33 diameter band, width 40 - 80 mm greater than the width of the band. The material for the steel rollers are 20GSL, 30GSL. The axis of the rollers are made of structural steels 45 and 50. Grease all bearings are managed centrally. To bandages did not descend from the rollers and the length of exposure is not less than 75% of its nominal value, rollers unfurl in a horizontal plane relative to the axis of the furnace at an angle of 10 - 450 so that occurs when this resistance force did not allow the drum to slide a distance greater than the thermal elongation .
Widespread roller with ball bearings and welded trusses, which allowed to greatly improve the reliability of the mechanical part of the furnace units and reduce the cost of their maintenance and repair.
For axial loads mounted pressure rollers. They are arranged so that they touch the side surface of one of the bands. Typically, pressure rollers made conical, so that they rolled on the surface of the band without slipping.
The latest advanced designs kilns supports the scheme is built on the principle of constant parallelism of the axes of rollers and the longitudinal axis of the furnace. The parallel arrangement of rollers provides a longer life tires and rollers at mensheyih width. In this case, the drum is held hydraulic system stops, which includes high-pressure hydraulic pumps, horizontal jacks and pressure rollers in contact with the end surface of bandages. longitudinal movement of the furnace is controlled automatically. By moving the furnace turns on the hydraulic pump, forcing oil under the piston of the jack. Jack pushes up the oven as long as the band reaches the stopper and turn off the pump. When the oven starts again shifted downward displacement restrictor again includes the pump and the cycle repeats. Cycle time displacement 24 - 48 hours.
Drive oven is usually set at equal distances from the ends of the drum. It consists of a pair of gear (drive gear and the crown) and the gear motor. The ring gear are made of quality carbon steel. To ensure longevity of the ring gear, which requires replacement of a long stoppage of the furnace, they are made of a harder material than the small (drive). large gears assembled from several sectors.
There are two types of fastening the ring gear to the drum: a tough and resilient. Rigid fixation (Fig. 79 a) used for the units, which body temperature during operation varies little and, hence, no thermal stresses. For average furnace crown resiliently fastened on the longitudinal (Fig. 99 b) or to the tangential plates. A crown secured to the longitudinal springs which in turn are rigidly fixed to steel at the edges of segments welded to the drum. When tangential connection (. Figure 99, c) one ends of the flat steel springs are rigidly attached to the drum, and the other - to the crown hinges. In large furnaces carried articulation rim and drum with the help of rods.
