- •1 Level (6 points)
- •History of the need for building materials
- •Cement production in the Republic of Kazakhstan
- •The history of obtaining and production cement
- •Economics of cement production
- •Determination of clinker, cement and additives introduced in the grinding
- •The composition of the raw meal. Equations 1-4
- •The composition of the raw meal. Equations 5-9
- •An overview of phase composition and quality phase of clinker
- •Portland cement clinker.
- •Chemical and mineralogical composition alite
- •Chemical and mineralogical composition of belite
- •Phase aluminate
- •Phase Ferrite
- •Other clinker phases
- •The composition and place of origin of the phases in portland cement clinker
- •Analysis of the raw meal, cement and clinker
- •Microscopic research of clinker
- •Recent developments in the use of X-rays
- •Petrographic analysis of clinker
- •Cement production
- •Raw materials and fuels in cement production
- •The raw materials of cement industry
- •Limestone and clay
- •A natural mixture of clay and limestone
- •Waste and their use in the cement industry
- •2 Level (6 points)
- •Mining, processing of raw materials, grinding of raw meal and homogenisation.
- •The blending warehouse of raw materials and its functions.
- •Development of the pile by rotary excavator
- •The process of burning cement clinker. General concepts
- •Chemical reactions during heat treatment of portland cement raw meal (main reaction clinker burning)
- •The dehydration of kaolinite
- •The reactions during the sintering
- •Reaction with cooling
- •Homogeneity of the raw meal
- •The process of burning cement clinker
- •Procedures for burning cement clinker
- •Decarbonizators with upward vertical gas flue.
- •The fuel in cement production
- •Clinker cooler
- •Cooler sf (Smidth-Fuller).
- •Storage of clinker
- •Cement Grinding
- •Milling equipment
- •The fineness of grinding and particle size distribution (grain) composition of the cement
- •Storage, packing, shipment cement to the consumer
- •The granulated blast furnace slag (s)
- •Pozzolan (p, q)
- •Natural pozzolanic additives (р)
- •Natural volcanic pozzolanic additives (q)
- •3 Level (8 points)
- •Fly ash rich in silica (V)
- •Lime ash dust (w)
- •Calcined shale (t)
- •Limestone (l, ll)
- •The quartz dust (d)
- •Small components
- •Calcium sulphate
- •The cement admixture
- •Cement according to standard
- •Physical and chemical properties of cements according to European standard
- •Cements with special properties
- •Well cement
- •Hydration
- •The reaction of silicates (c3s, c2s)
- •Hydration c3s
- •Hydration c2s
- •Reactions of hydration aluminate without participation of sulfates
- •Reactions hydration aluminate with participation sulphates
- •Hydration ferrite (c4af)
- •Taylor Model
- •Model Stark
- •The cement hydration
- •Reaction of the secondary components
- •Hydration of cement containing granulated slag
- •Reactions pozzolanic materials
- •4 Level (8 points)
- •Slowing solidification
- •Structure of a cement stone
- •Building lime
- •The historical and economic situation. Raw material deposits
- •Production and processing of limestone
- •Burning lime
- •Shaft kiln to coke (coal) and gas fuel
- •The rotary tube kiln
- •Counter current regenerative kiln (ggr-kiln)
- •Shaft ring kiln
- •Grinding and shipment of burnt lime
- •Slaked lime
- •The use of lime products
- •The requirements of stst 9179-79 to building lime
- •Gypsum. History and economy
- •Physical and chemical bases of gypsum binders
- •Phases in the system CaSo4 - h2o
- •The crystal structures, double salts, mixed crystals
- •Natural gypsum, natural anhydrite
- •The chemical gypsum
- •Uddg- gypsum
- •Production of calcium sulphate binders
- •Technological processes in the production of calcium sulphate binders
- •Autoclave method for producing α-hemihydrate
- •Gypsum boiling kettle for the production of ß-hemihydrate
- •5 Level (12 points)
- •The high temperature burning of gypsum method (multiphase gypsum) on the grate
- •Properties capable of hardening calcium sulphates
- •Hydration CaSo4-binding
- •Natural -, uusdg - and chemical anhydrite
- •The properties of the treated gypsum building materials
- •Other areas of application
- •The norms, chemical analysis and phase analysis
- •Gypsum Products
- •The requirements of gost 125-79 for the quality of construction gypsum
- •Other inorganic binding materials
- •Alumina cement
- •Production of alumina cement
- •Chemical and mineralogical composition of the alumina cement
- •Areas of use alumina cement
- •Softeners (plasticizers), added during the production concrete
- •Softeners (plasticizers), added to the concrete mix
- •Concrete
- •Mobile concrete plants
- •Concrete for precast concrete elements
- •Self-compacting concrete
- •Building mortar
- •Cement mortar
- •Plaster
- •Cementing deep wells
Grinding and shipment of burnt lime
Burnt lime is sent to consumers in the Federal Republic of Germany, mainly in the form of a fine lime. This underlines the importance attached to the process of production and consumption. Burnt lime is one of hard grind materials. Soft burnt lime grinding easier than more strictly (strongly) burned. Heavy fragmentation produced in the impact crusher, while the fine grinding is carried out in a ball or roller tube mills.
Burnt lime is sent to consumers in the Federal Republic of Germany, mainly in the form of a fine lime. This underlines the importance attached to the process of production and consumption. Burnt lime is one of hard grind materials. Soft burnt lime grinding easier than more strictly (strongly) burned. Heavy fragmentation produced in the impact crusher, while the fine grinding is carried out in a ball or roller tube mills. The conveyor circuit crushing plant is shown in Figure 1.54. There are several stages of quicklime powder lime. Snacha¬la absorbed water and raw powder is compacted by the formation of oxide hydroxide - CaO • 2H2O. Then a homogeneous dense mass turns into a "raging" powdered product. This releases a major amount of heat, leading to the heating supply and steam generation, as a result of spontaneous raz¬lozheniya oxyhydrate by the equation:
CaO • 2H2O → Ca (OH) 2 + H 2 O
The final stage - the formation of fluff, ie the appearance of aggregates of calcium hydroxide as a result of the mutual attraction of oppositely charged areas of single crystals of Ca (OH) 2...
For powder lime slaking in theory, must be 32.13% water by weight of quicklime. Practically water take 2 - 3 times more, since much of it evaporates. With a lack of water is overheated masses and "burnout" lime rezul¬tate in which some of its grain that failed to extinguish priob¬retayut dense structure, difficult to further gid¬ratatsii, and products cause a decrease in strength due to the late cancellation.
The amount of water required for slaking the dough depends on the quality of the lime, quenching method, and other factors. On average, it is approximately 2.5 liters per 1 kg of quicklime. The fatter the lime, the more water is needed. The water content in the final product - the limy test - usually no more than 50%.
The process of clearing burnt lime occurs [33] the faster and more completely:
- The more quality burnt lime, ie The higher content of CaO;
- More than svezheobozhzhennaya lime;
- The smaller pieces of lime;
- The lower the firing temperature of lime;
- The higher the temperature of the water supplied to the vapor pressure or quench.
1 - Crusher Lump lime 2 - bucket elevator, 3 - silage quicklime, 4 - dispenser, 5 - mixing screw, 6 - gasilny drum 7 - bucket elevators hydrate, 8 - separator 9 - screw 10 - shaker, 11 - fan humid air, 12 - spray chamber
Slaked lime
CaO in the hydration reaction of Ca (OH) 2 occurs at a considerable heat release (1159 kJ / kg CaO at 20 ° C) and technically referred to as hydrated lime. When 1 kg CaO slaking liberating sufficient heat to heat about 2.8 liters of water of 0 ° to 100 ° C. When slaked lime, depending on the amount of water can obtain lime - powder lime with a moisture content of not more than 5%, lime paste with a moisture content of about 50%, or milk of lime.
Blanking - special technological process used in the production of lime to¬lko. This process proceeds by the reaction:
CaO + H2O → Ca (OH) 2 + 1160 kJ / kg CaO
When slaked lime is released znachitel¬noe amount of heat 1160 kJ per 1 kg of calcium oxide. Vydelya¬yuschayasya heat causes boiling water, so called iz¬vest quicklime quicklime. Penetrating deep into the grain, the water enters into chemical interaction with CaO, and the heat released at the same time, turns the water into steam. The sharp increase of steam compared to the amount of liquid causes the internal stresses in rastyagiva¬yuschie lime grains and their destruction [165, 166, 167].
There are several stages of quicklime powder lime. Snacha¬la absorbed water and raw powder is compacted by the formation of oxide hydroxide - CaO • 2H2O. Then a homogeneous dense mass turns into a "raging" powdered product. This releases a major amount of heat, leading to the heating supply and steam generation, as a result of spontaneous raz¬lozheniya oxyhydrate by the equation:
CaO • 2H2O → Ca (OH) 2 + H 2 O
The final stage - the formation of fluff, ie the appearance of aggregates of calcium hydroxide as a result of the mutual attraction of oppositely charged areas of single crystals of Ca (OH) 2...
For powder lime slaking in theory, must be 32.13% water by weight of quicklime. Practically water take 2 - 3 times more, since much of it evaporates. With a lack of water is overheated masses and "burnout" lime rezul¬tate in which some of its grain that failed to extinguish priob¬retayut dense structure, difficult to further gid¬ratatsii, and products cause a decrease in strength due to the late cancellation.
The amount of water required for slaking the dough depends on the quality of the lime, quenching method, and other factors. On average, it is approximately 2.5 liters per 1 kg of quicklime. The fatter the lime, the more water is needed. The water content in the final product - the limy test - usually no more than 50%.
The process of clearing is slow due to the formation on the surface of the lime particles doughy layer prepyatstvu¬yuschego access of water to unslaked inner layers. To speed up the process of extinction of lime is recommended mechanical effect - mixing vibration, as this breaks with the unreacted particles of shell Ca (OH) 2.
The rate of interaction of calcium oxide with water and sootvetst¬venno speed damping at higher temperatures for every 10 ° C increase in 2 times, so it is advisable to extinguish lime at elevated steam pressure in special drums.
On quenching speed is also influenced by various additives vvodi¬mye water. For example, chloride salts (NaCl, SaS12i al.) Increase the rate of quenching, gypsum and additives and surfactant significantly slow the hydration of CaO.
The character blanking process is dependent on the presence of impurities. When quenching in fluff grains silicates and calcium aluminates, a converted-on during firing is not blanked and not converted into a powder - they must be separate, and be mixed with comminuted fluff to improve its properties.
Figure 1.55 shows a flow chart gasilnoy lime plant.
The process of clearing burnt lime occurs [33] the faster and more completely:
- The more quality burnt lime, ie The higher content of CaO;
- More than svezheobozhzhennaya lime;
- The smaller pieces of lime;
- The lower the firing temperature of lime;
- The higher the temperature of the water supplied to the vapor pressure or quench.
1 - Crusher Lump lime 2 - bucket elevator, 3 - silage quicklime, 4 - dispenser, 5 - mixing screw, 6 - gasilny drum 7 - bucket elevators hydrate, 8 - separator 9 - screw 10 - shaker, 11 - fan humid air, 12 - spray chamber
