- •Foreword
- •General Information Table of Contents
- •Inspection
- •Instrument
- •Model Identification
- •Technical Information - Cassette Type Transmission
- •Technical Information - Inlet Air Pressure Sensor
- •Inlet Solenoid Valve
- •Unit Conversion Table Prefixes for Units:
- •Units of Power:
- •Periodic Maintenance Table of Contents
- •Idle Speed Inspection ....................................................................................................... 2-18
- •Idle Speed Adjustment...................................................................................................... 2-18
- •Valve Clearance Inspection .............................................................................................. 2-21
- •Valve Clearance Adjustment............................................................................................. 2-23
- •Periodic Inspection
- •Basic Torque for General Fasteners
- •Specifications
- •Special Tools
- •Inside Circlip Pliers: 57001-143
- •Fuel System (dfi)
- •Idle Speed Inspection
- •Idle Speed
- •Idle Speed Adjustment
- •Evaporative Emission Control System (California Model)
- •Cooling System
- •Air Suction System
- •Engine Top End
- •Valve Clearance Inspection
- •Valve clearance adjustment chart inlet valve
- •Valve clearance adjustment chart exhaust valve
- •Wheels/Tires
- •(Over 130 km/h (80 mph))
- •Drive Train
- •Brake System
- •Suspensions
- •Steering System
- •Electrical System
- •Replacement Parts
- •Viscosity: sae 10w-40
- •1.9 L (2.0 us qt) (when filter is removed)
- •2.4 L (2.5 us qt) (when engine is completely dry) note
- •It does not reach to this tightening torque.
- •Fuel System (dfi) Table of Contents
- •Inquiries to Rider.................................................................................................................. 3-26
- •Inquiries to Rider............................................................................................................... 3-26
- •Terminal Names
- •Dfi Parts Location
- •Specifications
- •Special Tools and Sealant
- •Dfi Servicing Precautions
- •Dfi Servicing Precautions
- •Inquiries to Rider
- •Inquiries to Rider
- •Sample Diagnosis Sheet
- •Engine Doesn’t Start, Starting Difficulty
- •Self-diagnosis Procedures
- •Service Code Clearing Procedures
- •How to Erase Service Codes
- •Backups
- •Idle Speed Standard: 1 300 ±50 r/min (rpm)
- •Inlet Air Pressure Sensor Removal
- •Inlet Air Pressure Sensor Installation
- •Inlet Air Pressure Sensor Input Voltage Inspection note
- •Inlet Air Pressure Sensor Input Voltage Connections to ecu
- •Inlet Air Pressure Sensor Output Voltage Inspection note
- •Inlet Air Pressure Sensor Output Voltage Connections to ecu
- •Inlet Air Pressure Sensor Output Voltage Connection to Adapter
- •Inlet Air Pressure Sensor Circuit
- •Inlet Air Temperature Sensor (Service Code 13)
- •Inlet Air Temperature Sensor Removal/Installation
- •Inlet Air Temperature Sensor Output Voltage Inspection note
- •Inlet Air Temperature Sensor Output Voltage Connections to ecu Connector
- •Inlet Air Temperature Sensor (Service Code 13)
- •Inlet Air Temperature Sensor Resistance Inspection
- •Inlet Air Temperature Sensor Circuit
- •Water Temperature Sensor (Service Code 14)
- •Water Temperature Sensor (Service Code 14)
- •Crankshaft Sensor (Service Code 21)
- •Speed Sensor (Service Code 24, 25)
- •Speed Sensor (Service Code 24, 25)
- •Vehicle-down Sensor (Service Code 31)
- •Vehicle-down Sensor Output Voltage Connections to Sensor
- •Vehicle-down Sensor Circuit
- •Oxygen Sensor-not activated (Service Code 33) (Europe Models)
- •Oxygen Sensor-not activated (Service Code 33) (Europe Models)
- •Stick Coils #1, #2: (Service Code 51, 52)
- •Stick Coil Removal/Installation
- •Input Voltage at ecu
- •Stick Coils #1, #2: (Service Code 51, 52)
- •Radiator Fan Relay (Service Code 56)
- •Subthrottle Valve Actuator (Service Code 62)
- •Subthrottle Valve Actuator (Service Code 62)
- •Input Voltage at Actuator
- •Air Switching Valve (Service Code 64)
- •Oxygen Sensor Heater (Service Code 67) (Europe Models)
- •Oxygen Sensor Heater (Service Code 67) (Europe Models)
- •Fi Indicator Light (led)
- •Inspection Flow Chart
- •Oxygen Sensor-Incorrect Output Voltage (Service Code 94) (Europe Models)
- •Oxygen Sensor-Incorrect Output Voltage (Service Code 94) (Europe Models)
- •Ignition Switch off: Terminal 16 (br/w): 0 V
- •Needle Adapter Set: 57001-1457
- •Standard: Battery Voltage (12.8 V or more) for 3 seconds, and then 0 V.
- •Injector Output Voltage Connections to Injector #1
- •Injector Wiring Inspection
- •Injector Signal Test
- •Injector Resistance Inspection
- •Injector Resistance Connections to Injector
- •#1: W/r ←→ bl/r Terminal #2: w/r ←→ bl/g Terminal
- •Injector Unit Test
- •Injector Fuel Line Inspection
- •Injector Fuel Line Maximum Pressure Standard: 333 kPa (3.4 kgf/cm², 48 psi)
- •Idle Speed Inspection
- •Throttle Body Assy
- •Throttle Body Assy
- •Air Cleaner
- •Air Cleaner
- •Evaporative Emission Control System (California Model)
- •Evaporative Emission Control System (California Model)
- •Cooling System Table of Contents
- •Exploded View
- •Coolant Flow Chart
- •Specifications
- •Coolant
- •Coolant
- •Water Pump
- •Impeller Assembly
- •Thermostat
- •Thermostat
- •Hose and Pipes
- •Water Temperature Sensor
- •Engine Top End Table of Contents
- •Exhaust System
- •Exhaust System
- •Specifications
- •Special Tools and Sealant
- •Clean Air System
- •Clean Air System
- •Cylinder Head Cover
- •Cylinder Head Cover
- •Camshaft Chain Tensioner
- •Inlet 36.44 mm (1.4346 in.)
- •Valve Guide Removal
- •Valve Guide Installation
- •Valve-to-Guide Clearance Measurement (Wobble Method)
- •Throttle Body Holder
- •Muffler
- •Muffler
- •Clutch Table of Contents
- •Exploded View
- •Specifications
- •Clutch Lever and Cable
- •Clutch Lever and Cable
- •Clutch Cover
- •Engine Lubrication System Table of Contents
- •Exploded View
- •Engine Oil Flow Chart
- •Engine Oil and Oil Filter
- •Oil Pressure Relief Valve
- •Oil Pump
- •Oil Pump
- •Oil Pressure Measurement
- •Oil Pressure Switch
- •Engine Removal/Installation Table of Contents
- •Exploded View
- •Crankshaft/Transmission Table of Contents
- •Balancer
- •Balancer
- •Balancer Shaft Bearing Insert Selection
- •Ball Bearing, Needle Bearing, and Oil Seal
- •Wheels/Tires Table of Contents
- •Exploded View
- •Specifications
- •Service Limit:
- •Hub Bearing
- •Hub Bearing
- •Final Drive Table of Contents
- •Exploded View
- •Specifications
- •Inside Circlip Pliers: 57001-143
- •Brakes Table of Contents
- •Specifications
- •Inside Circlip Pliers: 57001-143
- •Brake Lever, Brake Pedal
- •Brake Disc
- •Brake Fluid
- •Inquiries to Rider
- •Sample Diagnosis Sheet
- •Service Code Table
- •Suspension Table of Contents
- •Specifications
- •Inside Circlip Pliers: 57001-143
- •Special Tools
- •Viscosity: kayaba khl34-g10 or equivalent
- •Inner Tube Inspection
- •Rear Shock Absorber
- •Special Tools - Jack: 57001-1238
- •Rear Shock Absorber
- •Jack Attachment: 57001-1608
- •Steering Table of Contents
- •Exploded View
- •Special Tools
- •Steering
- •Handlebar
- •Handlebar
- •Frame Table of Contents
- •Inner Fairing Removal
- •Inner Fairing Installation
- •Side Covers
- •Seat Covers
- •Fenders
- •Fenders
- •Sidestand
- •Frame Cover
- •Electrical System Table of Contents
- •Specifications
- •Parts Location
- •Parts Location
- •Wiring Diagram (Europe, Korea, Hong Kong and Kuwait)
- •Precautions
- •Electrical Wiring
- •Initial Charge
- •Interchange
- •Rotor Holder: 57001-1658
- •Interlock Operation Inspection
- •1St Check
- •2Nd Check
- •3Rd Check
- •Ic Igniter Inspection
- •Ignition System Circuit
- •Air Switching Valve
- •Air Switching Valve
- •Radiator Fan System
- •Indicator Lights Inspection
- •12 V 3.4 w Bulb (Other Side) → bl Lead Terminal Battery (–) → bk Lead Terminal
- •30 A Main Fuse Removal
- •15 A ecu Fuse Removal
- •Appendix Table of Contents
- •Engine Doesn’t Start, Starting Difficulty:
- •Poor Running at Low Speed:
- •Poor Running or No Power at High Speed:
- •Overheating:
- •Over Cooling:
- •Clutch Operation Faulty:
- •Gear Shifting Faulty:
- •Abnormal Engine Noise:
- •Valve noise:
- •Abnormal Drive Train Noise:
- •Battery Trouble:
- •Model application
Basic Torque for General Fasteners
Threads Diameter (mm) |
Torque |
||
N·m |
kgf·m |
ft·lb |
|
5 |
3.4 4.9 |
0.35 0.50 |
30 43 in·lb |
6 |
5.9 7.8 |
0.60 0.80 |
52 69 in·lb |
8 |
14 19 |
1.4 1.9 |
10.0 13.5 |
10 |
25 34 |
2.6 3.5 |
19.0 25 |
12 |
44 61 |
4.5 6.2 |
33 45 |
14 |
73 98 |
7.4 10.0 |
54 72 |
16 |
115 155 |
11.5 16.0 |
83 115 |
18 |
165 225 |
17.0 23.0 |
125 165 |
20 |
225 325 |
23.0 33.0 |
165 240 |
Specifications
Item |
Standard |
Service Limit |
Fuel System (DFI) Throttle Grip Free Play Idle Speed Bypass Screws (Turn Out) Engine Vacuum Air Cleaner Element |
2 3 mm (0.08 0.12 in.) 1 300 ±50 r/min (rpm) 0 2 1/2 (for reference) 35.3 ±1.3 kPa (265 ±10 mmHg) Polyurethane Foam |
– – – – – – – – – – – – – – – |
Cooling System Coolant: Type (recommended) Color Mixed Ratio Freezing Point Total Amount |
Permanent type of antifreeze Green Soft water 50%, Coolant 50% –35°C (–31°F) 1.2 L (1.3 US qt) |
– – – – – – – – – – – – – – – |
Engine Top End Valve Clearance: Exhaust Inlet |
0.22 0.31 mm (0.0087 0.0122 in.) 0.15 0.21 mm (0.0059 0.0083 in.) |
– – – – – – |
Clutch Clutch Lever Free Play |
2 3 mm (0.08 0.12 in.) |
– – – |
Engine Lubrication System Engine Oil: Type
Viscosity Capacity
Level |
API SE, SF or SG API SH, SJ or SL with JASO MA SAE 10W-40 1.7 L (1.8 US qt) (when filter is not removed) 1.9 L (2.0 US qt) (when filter is removed) 2.4 L (2.5 US qt) (when engine is completely dry) Between upper and lower level lines (after idling or running) |
– – –
– – – – – –
– – – – – –
– – – |
Wheels/Tires Tread Depth: Front
Rear
Air Pressure (when Cold): Front
Rear |
4.3 mm (0.17 in.)
7.0 mm (0.28 in.)
Up to 180 kg (397 lb) load: 225 kPa (2.25 kgf/cm², 32 psi) Up to 180 kg (397 lb) load: 250 kPa (2.50 kgf/cm², 36 psi) |
1 mm (0.04 in.), (AT, CH, DE) 1.6 mm (0.06 in.) Up to 130 km/h (80 mph): 2 mm (0.08 in.), Over 130 km/h (80 mph): 3 mm (0.12 in.)
– – –
– – – |
Specifications
Item |
Standard |
Service Limit |
Final Drive Drive Chain Slack Drive Chain Wear (20-link Length) Standard Chain: Make Type Link |
30 40 mm (1.2 1.6 in.) |
– – – |
317.5 318.2 mm (12.50 12.53 in.) |
323 mm (12.7 in.) |
|
ENUMA |
– – – |
|
EK520MVXL1 |
– – – |
|
114 links |
– – – |
|
Brakes Brake Fluid: Grade Brake Pad Lining Thickness: Front Rear Brake Light Timing: Front Rear |
DOT4 |
– – – |
4.5 mm (0.18 in.) |
1 mm (0.04 in.) |
|
5.0 mm (0.20 in.) |
1 mm (0.04 in.) |
|
Pulled ON |
– – – |
|
ON after about 10 mm (0.39 in.) of pedal travel |
– – – |
|
Electrical System Spark Plug Gap |
0.8 0.9 mm (0.03 0.04 in.) |
– – – |
