Добавил:
Upload Опубликованный материал нарушает ваши авторские права? Сообщите нам.
Вуз: Предмет: Файл:
ER-6_06-08_Manual.docx
Скачиваний:
1
Добавлен:
01.07.2025
Размер:
35 Мб
Скачать
☆

Replacement Parts

Air Cleaner Element Replacement

• Refer to the Air Cleaner Element Cleaning.

Fuel Hose Replacement

• Remove:

Fuel Tank (see Fuel Tank Removal in the Fuel System

(DFI) chapter)

Left Center Fairing (see Center Fairing Removal in the Frame chapter)

• Be sure to place a piece of cloth [A] around the fuel hose

joint.

• Insert a minus screw driver [B] into the slit [C] on the joint lock.

• Turn [A] the driver to disconnect the joint lock [B].

• Pull [C] the fuel hose joint [D] out of the delivery pipe.

• Install the new fuel hose.

• Insert [A] the fuel hose joint [B] straight onto the delivery

pipe until the hose joint clicks.

• Push [C] the joint lock [D].

• Push and pull [A] the fuel hose joint [B] back and forth more than two times and make sure it is locked and

doesn’t come off.

If it comes off, reinstall the hose joint.

• Run the fuel hose correctly (see Cable, Wire, and Hose Routing section in the Appendix chapter).

• Install the removed parts (see appropriate chapters).

• Start the engine and check the fuel hose for leaks.

Coolant Change

• Remove:

Right Center Fairing (see Center Fairing Removal in the

Frame chapter) Reserve Tank Bolts [A] Reserve Tank [B]

• Put [A] the projection [B] on the reserve tank into the hole [C] on the frame bracket, and place the reserve tank on

the right side of frame.

• Place a container under the water pump drain bolt [A], then remove the drain bolt.

• Remove the radiator cap [A] in two steps. First turn the cap counterclockwise to the first stop. Then push and turn

it further in the same direction and remove the cap.

○The coolant will drain from the radiator and engine.

• Turn over [A] the reserve tank, remove the cap, and pour the coolant into a suitable container.

• Place the reserve tank on the right side of frame.

• Tighten the drain bolt with the gasket.

○Replace the drain bolt gasket with a new one.

Torque - Water Pump Drain Bolt: 7.0 N·m (0.70 kgf·m, 62 in·lb)

• When filling the coolant, choose a suitable mixture ratio by referring to the coolant manufacturer’s directions.

Water and Coolant Mixture Ratio (Recommended) Soft Water: 50%

Coolant: 50%

Freezing Point: –35°C (–31°F) Total Amount: 1.2 L (1.3 US qt)

• Fill the radiator up to the filler neck [A] with coolant.

NOTE

○Pour in the coolant slowly so that it can expel the air

from the engine and radiator.

• Check the cooling system for leaks.

• Tap the radiator hoses to force any air bubbles caught

inside.

• Fill the radiator up to the filler neck with coolant.

• Temporarily install the reserve tank to the frame with two bolts.

• Fill the reserve tank up to the “F” (full) level line [A] with

coolant and install the cap [B].

• Start the engine, warm it up thoroughly until the radiator fan turns on and then stop the engine.

• Check the coolant level in the reserve tank after the en-

gine cools down.

If the coolant level is lower than the “L” level line, add coolant to the “F” level line.

Radiator Hose and O-ring Replacement

• Drain the coolant (see Coolant Change).

• Remove:

Thermostat Housing [A] (see Water Pump Removal in

the Cooling System chapter)

Water Pump Cover [B] (see Water Pump Removal in the Cooling System chapter)

Hoses [C] O-rings [D]

• Apply grease to the new O-rings and install them.

• Install the new hoses and tighten the clamps securely.

• Fill the coolant (see Coolant Change).

• Check the cooling system for leaks.

Engine Oil Change

• Situate the motorcycle so that it is vertical after warming up the engine.

• Unscrew the oil filler plug [A].

• Place on oil pan beneath the engine.

• Remove the engine oil drain bolt [A] to drain the oil.

○The oil in the oil filter can be drained by removing the filter

(see Oil Filter Replacement).

Replace the drain bolt gasket [B] with a new one.

• Tighten the drain bolt.

Torque - Engine Oil Drain Bolt: 30 N·m (3.0 kgf·m, 22 ft·lb)

• Pour in the specified type and amount of oil.

Recommended Engine Oil

Type: API SE, SF or SG

API SH, SJ or SL with JASO MA

Соседние файлы в предмете [НЕСОРТИРОВАННОЕ]