- •Foreword
- •General Information Table of Contents
- •Inspection
- •Instrument
- •Model Identification
- •Technical Information - Cassette Type Transmission
- •Technical Information - Inlet Air Pressure Sensor
- •Inlet Solenoid Valve
- •Unit Conversion Table Prefixes for Units:
- •Units of Power:
- •Periodic Maintenance Table of Contents
- •Idle Speed Inspection ....................................................................................................... 2-18
- •Idle Speed Adjustment...................................................................................................... 2-18
- •Valve Clearance Inspection .............................................................................................. 2-21
- •Valve Clearance Adjustment............................................................................................. 2-23
- •Periodic Inspection
- •Basic Torque for General Fasteners
- •Specifications
- •Special Tools
- •Inside Circlip Pliers: 57001-143
- •Fuel System (dfi)
- •Idle Speed Inspection
- •Idle Speed
- •Idle Speed Adjustment
- •Evaporative Emission Control System (California Model)
- •Cooling System
- •Air Suction System
- •Engine Top End
- •Valve Clearance Inspection
- •Valve clearance adjustment chart inlet valve
- •Valve clearance adjustment chart exhaust valve
- •Wheels/Tires
- •(Over 130 km/h (80 mph))
- •Drive Train
- •Brake System
- •Suspensions
- •Steering System
- •Electrical System
- •Replacement Parts
- •Viscosity: sae 10w-40
- •1.9 L (2.0 us qt) (when filter is removed)
- •2.4 L (2.5 us qt) (when engine is completely dry) note
- •It does not reach to this tightening torque.
- •Fuel System (dfi) Table of Contents
- •Inquiries to Rider.................................................................................................................. 3-26
- •Inquiries to Rider............................................................................................................... 3-26
- •Terminal Names
- •Dfi Parts Location
- •Specifications
- •Special Tools and Sealant
- •Dfi Servicing Precautions
- •Dfi Servicing Precautions
- •Inquiries to Rider
- •Inquiries to Rider
- •Sample Diagnosis Sheet
- •Engine Doesn’t Start, Starting Difficulty
- •Self-diagnosis Procedures
- •Service Code Clearing Procedures
- •How to Erase Service Codes
- •Backups
- •Idle Speed Standard: 1 300 ±50 r/min (rpm)
- •Inlet Air Pressure Sensor Removal
- •Inlet Air Pressure Sensor Installation
- •Inlet Air Pressure Sensor Input Voltage Inspection note
- •Inlet Air Pressure Sensor Input Voltage Connections to ecu
- •Inlet Air Pressure Sensor Output Voltage Inspection note
- •Inlet Air Pressure Sensor Output Voltage Connections to ecu
- •Inlet Air Pressure Sensor Output Voltage Connection to Adapter
- •Inlet Air Pressure Sensor Circuit
- •Inlet Air Temperature Sensor (Service Code 13)
- •Inlet Air Temperature Sensor Removal/Installation
- •Inlet Air Temperature Sensor Output Voltage Inspection note
- •Inlet Air Temperature Sensor Output Voltage Connections to ecu Connector
- •Inlet Air Temperature Sensor (Service Code 13)
- •Inlet Air Temperature Sensor Resistance Inspection
- •Inlet Air Temperature Sensor Circuit
- •Water Temperature Sensor (Service Code 14)
- •Water Temperature Sensor (Service Code 14)
- •Crankshaft Sensor (Service Code 21)
- •Speed Sensor (Service Code 24, 25)
- •Speed Sensor (Service Code 24, 25)
- •Vehicle-down Sensor (Service Code 31)
- •Vehicle-down Sensor Output Voltage Connections to Sensor
- •Vehicle-down Sensor Circuit
- •Oxygen Sensor-not activated (Service Code 33) (Europe Models)
- •Oxygen Sensor-not activated (Service Code 33) (Europe Models)
- •Stick Coils #1, #2: (Service Code 51, 52)
- •Stick Coil Removal/Installation
- •Input Voltage at ecu
- •Stick Coils #1, #2: (Service Code 51, 52)
- •Radiator Fan Relay (Service Code 56)
- •Subthrottle Valve Actuator (Service Code 62)
- •Subthrottle Valve Actuator (Service Code 62)
- •Input Voltage at Actuator
- •Air Switching Valve (Service Code 64)
- •Oxygen Sensor Heater (Service Code 67) (Europe Models)
- •Oxygen Sensor Heater (Service Code 67) (Europe Models)
- •Fi Indicator Light (led)
- •Inspection Flow Chart
- •Oxygen Sensor-Incorrect Output Voltage (Service Code 94) (Europe Models)
- •Oxygen Sensor-Incorrect Output Voltage (Service Code 94) (Europe Models)
- •Ignition Switch off: Terminal 16 (br/w): 0 V
- •Needle Adapter Set: 57001-1457
- •Standard: Battery Voltage (12.8 V or more) for 3 seconds, and then 0 V.
- •Injector Output Voltage Connections to Injector #1
- •Injector Wiring Inspection
- •Injector Signal Test
- •Injector Resistance Inspection
- •Injector Resistance Connections to Injector
- •#1: W/r ←→ bl/r Terminal #2: w/r ←→ bl/g Terminal
- •Injector Unit Test
- •Injector Fuel Line Inspection
- •Injector Fuel Line Maximum Pressure Standard: 333 kPa (3.4 kgf/cm², 48 psi)
- •Idle Speed Inspection
- •Throttle Body Assy
- •Throttle Body Assy
- •Air Cleaner
- •Air Cleaner
- •Evaporative Emission Control System (California Model)
- •Evaporative Emission Control System (California Model)
- •Cooling System Table of Contents
- •Exploded View
- •Coolant Flow Chart
- •Specifications
- •Coolant
- •Coolant
- •Water Pump
- •Impeller Assembly
- •Thermostat
- •Thermostat
- •Hose and Pipes
- •Water Temperature Sensor
- •Engine Top End Table of Contents
- •Exhaust System
- •Exhaust System
- •Specifications
- •Special Tools and Sealant
- •Clean Air System
- •Clean Air System
- •Cylinder Head Cover
- •Cylinder Head Cover
- •Camshaft Chain Tensioner
- •Inlet 36.44 mm (1.4346 in.)
- •Valve Guide Removal
- •Valve Guide Installation
- •Valve-to-Guide Clearance Measurement (Wobble Method)
- •Throttle Body Holder
- •Muffler
- •Muffler
- •Clutch Table of Contents
- •Exploded View
- •Specifications
- •Clutch Lever and Cable
- •Clutch Lever and Cable
- •Clutch Cover
- •Engine Lubrication System Table of Contents
- •Exploded View
- •Engine Oil Flow Chart
- •Engine Oil and Oil Filter
- •Oil Pressure Relief Valve
- •Oil Pump
- •Oil Pump
- •Oil Pressure Measurement
- •Oil Pressure Switch
- •Engine Removal/Installation Table of Contents
- •Exploded View
- •Crankshaft/Transmission Table of Contents
- •Balancer
- •Balancer
- •Balancer Shaft Bearing Insert Selection
- •Ball Bearing, Needle Bearing, and Oil Seal
- •Wheels/Tires Table of Contents
- •Exploded View
- •Specifications
- •Service Limit:
- •Hub Bearing
- •Hub Bearing
- •Final Drive Table of Contents
- •Exploded View
- •Specifications
- •Inside Circlip Pliers: 57001-143
- •Brakes Table of Contents
- •Specifications
- •Inside Circlip Pliers: 57001-143
- •Brake Lever, Brake Pedal
- •Brake Disc
- •Brake Fluid
- •Inquiries to Rider
- •Sample Diagnosis Sheet
- •Service Code Table
- •Suspension Table of Contents
- •Specifications
- •Inside Circlip Pliers: 57001-143
- •Special Tools
- •Viscosity: kayaba khl34-g10 or equivalent
- •Inner Tube Inspection
- •Rear Shock Absorber
- •Special Tools - Jack: 57001-1238
- •Rear Shock Absorber
- •Jack Attachment: 57001-1608
- •Steering Table of Contents
- •Exploded View
- •Special Tools
- •Steering
- •Handlebar
- •Handlebar
- •Frame Table of Contents
- •Inner Fairing Removal
- •Inner Fairing Installation
- •Side Covers
- •Seat Covers
- •Fenders
- •Fenders
- •Sidestand
- •Frame Cover
- •Electrical System Table of Contents
- •Specifications
- •Parts Location
- •Parts Location
- •Wiring Diagram (Europe, Korea, Hong Kong and Kuwait)
- •Precautions
- •Electrical Wiring
- •Initial Charge
- •Interchange
- •Rotor Holder: 57001-1658
- •Interlock Operation Inspection
- •1St Check
- •2Nd Check
- •3Rd Check
- •Ic Igniter Inspection
- •Ignition System Circuit
- •Air Switching Valve
- •Air Switching Valve
- •Radiator Fan System
- •Indicator Lights Inspection
- •12 V 3.4 w Bulb (Other Side) → bl Lead Terminal Battery (–) → bk Lead Terminal
- •30 A Main Fuse Removal
- •15 A ecu Fuse Removal
- •Appendix Table of Contents
- •Engine Doesn’t Start, Starting Difficulty:
- •Poor Running at Low Speed:
- •Poor Running or No Power at High Speed:
- •Overheating:
- •Over Cooling:
- •Clutch Operation Faulty:
- •Gear Shifting Faulty:
- •Abnormal Engine Noise:
- •Valve noise:
- •Abnormal Drive Train Noise:
- •Battery Trouble:
- •Model application
Needle Adapter Set: 57001-1457
○Measure the operating voltage with the engine stopped, and with the connector joined.
• Turn the ignition switch ON.
○The tester needle should indicate battery voltage for 3
seconds, and then 0 V.
Pump Operating Voltage at Pump Connections to Pump Connectors
Tester (+) → W/R Lead Tester (–) → BK/Y Lead
Operating Voltage at Pump Connector
Standard: Battery Voltage (12.8 V or more) for 3 seconds, and then 0 V.
If the reading stays on battery voltage, and never shows 0 V. Check the ECU and fuel pump relay.
If the voltage is in specification, but the pump doesn’t work, replace the pump (see Fuel Pump Removal/Instal- lation).
If there is still no battery voltage, check the pump relay (see Relay Box section in the Electrical System chapter).
Pressure
Regulator Removal
○The pressure regulator [A] is built into the fuel pump [B]
and cannot be removed.
Pump
Screen, Fuel Filter Cleaning
○The fuel filter [A] is built into the pump and cannot be
cleaned or checked.
If the fuel filter is suspected of clogging or being damaged, replace it with the fuel pump as a set.
Fuel
Pump Circuit
ECU
Water-proof Joint C
Engine Stop Switch
Ignition Switch
Ignition Fuse 10 A
Fuel Pump Relay
Relay Box
Main Fuse 30 A
Battery
Frame Ground
Fuel Pump
Removal/Installation
•
Refer to the Throttle Body Assy Disassembly/Assembly.
Audible Inspection
• Start the engine.
• Apply the tip of a screwdriver [A] to the injector [B]. Put
the grip end onto your ear, and listen whether the injector
is clicking or not.
○A sound scope [C] can also be used.
• Do the same for the other injectors.
If all the injectors click at a regular intervals, the injec-
tors
are good.
The trouble
may be
related to
the fuel
line, requiring fuel pressure inspection (see Fuel Pressure
In- spection).
○The click interval becomes shorter as the engine speed
rises.
If any injector(s) doesn’t click, the DFI circuit or the injector is suspect. Perform “Fuel Injector Power Source Voltage Inspection”, first.
Fuel
Injector Power Source Voltage Inspection
• Remove the ECU (see ECU Removal).
○Do not disconnect the ECU connector.
• Connect a digital meter [A] to the ECU connector [B], us- ing the needle adapter [C].
Special Tool - Needle Adapter Set: 57001-1457
○Measure the power source voltage with the engine stopped, and with the connector joined.
• Turn the ignition switch ON.
Injector Power Source Voltage at ECU Connections: Meter (+) → W/Y (terminal 16)
Meter (–) → Battery (–) Terminal Service Limit: Battery Voltage (12.8 V or more)
If the meter doesn’t read as specified, check the following. Main Fuse 30 A (see Fuse Inspection in the Electrical System chapter)
Fuel Pump Relay (see Relay Circuit Inspection in the Electrical System chapter)
Power Source Wiring (see wiring diagram below)
○To check the W/R leads between the injector connector
and the fuel pump relay, remove the fuel tank (see Fuel
Tank Removal) and the left side cover (see Side Cover Removal in the Frame chapter).
If the power source voltage is normal, check the output voltage of the injectors.
Fuel Injector Output Voltage Inspection
•
Turn the ignition switch OFF.
• Remove the ECU (see ECU Removal).
• Connect a digital voltmeter [A] to the ECU connector [B]
with the needle adapter set [C].
Special Tool - Needle Adapter Set: 57001-1457
