- •Foreword
- •General Information Table of Contents
- •Inspection
- •Instrument
- •Model Identification
- •Technical Information - Cassette Type Transmission
- •Technical Information - Inlet Air Pressure Sensor
- •Inlet Solenoid Valve
- •Unit Conversion Table Prefixes for Units:
- •Units of Power:
- •Periodic Maintenance Table of Contents
- •Idle Speed Inspection ....................................................................................................... 2-18
- •Idle Speed Adjustment...................................................................................................... 2-18
- •Valve Clearance Inspection .............................................................................................. 2-21
- •Valve Clearance Adjustment............................................................................................. 2-23
- •Periodic Inspection
- •Basic Torque for General Fasteners
- •Specifications
- •Special Tools
- •Inside Circlip Pliers: 57001-143
- •Fuel System (dfi)
- •Idle Speed Inspection
- •Idle Speed
- •Idle Speed Adjustment
- •Evaporative Emission Control System (California Model)
- •Cooling System
- •Air Suction System
- •Engine Top End
- •Valve Clearance Inspection
- •Valve clearance adjustment chart inlet valve
- •Valve clearance adjustment chart exhaust valve
- •Wheels/Tires
- •(Over 130 km/h (80 mph))
- •Drive Train
- •Brake System
- •Suspensions
- •Steering System
- •Electrical System
- •Replacement Parts
- •Viscosity: sae 10w-40
- •1.9 L (2.0 us qt) (when filter is removed)
- •2.4 L (2.5 us qt) (when engine is completely dry) note
- •It does not reach to this tightening torque.
- •Fuel System (dfi) Table of Contents
- •Inquiries to Rider.................................................................................................................. 3-26
- •Inquiries to Rider............................................................................................................... 3-26
- •Terminal Names
- •Dfi Parts Location
- •Specifications
- •Special Tools and Sealant
- •Dfi Servicing Precautions
- •Dfi Servicing Precautions
- •Inquiries to Rider
- •Inquiries to Rider
- •Sample Diagnosis Sheet
- •Engine Doesn’t Start, Starting Difficulty
- •Self-diagnosis Procedures
- •Service Code Clearing Procedures
- •How to Erase Service Codes
- •Backups
- •Idle Speed Standard: 1 300 ±50 r/min (rpm)
- •Inlet Air Pressure Sensor Removal
- •Inlet Air Pressure Sensor Installation
- •Inlet Air Pressure Sensor Input Voltage Inspection note
- •Inlet Air Pressure Sensor Input Voltage Connections to ecu
- •Inlet Air Pressure Sensor Output Voltage Inspection note
- •Inlet Air Pressure Sensor Output Voltage Connections to ecu
- •Inlet Air Pressure Sensor Output Voltage Connection to Adapter
- •Inlet Air Pressure Sensor Circuit
- •Inlet Air Temperature Sensor (Service Code 13)
- •Inlet Air Temperature Sensor Removal/Installation
- •Inlet Air Temperature Sensor Output Voltage Inspection note
- •Inlet Air Temperature Sensor Output Voltage Connections to ecu Connector
- •Inlet Air Temperature Sensor (Service Code 13)
- •Inlet Air Temperature Sensor Resistance Inspection
- •Inlet Air Temperature Sensor Circuit
- •Water Temperature Sensor (Service Code 14)
- •Water Temperature Sensor (Service Code 14)
- •Crankshaft Sensor (Service Code 21)
- •Speed Sensor (Service Code 24, 25)
- •Speed Sensor (Service Code 24, 25)
- •Vehicle-down Sensor (Service Code 31)
- •Vehicle-down Sensor Output Voltage Connections to Sensor
- •Vehicle-down Sensor Circuit
- •Oxygen Sensor-not activated (Service Code 33) (Europe Models)
- •Oxygen Sensor-not activated (Service Code 33) (Europe Models)
- •Stick Coils #1, #2: (Service Code 51, 52)
- •Stick Coil Removal/Installation
- •Input Voltage at ecu
- •Stick Coils #1, #2: (Service Code 51, 52)
- •Radiator Fan Relay (Service Code 56)
- •Subthrottle Valve Actuator (Service Code 62)
- •Subthrottle Valve Actuator (Service Code 62)
- •Input Voltage at Actuator
- •Air Switching Valve (Service Code 64)
- •Oxygen Sensor Heater (Service Code 67) (Europe Models)
- •Oxygen Sensor Heater (Service Code 67) (Europe Models)
- •Fi Indicator Light (led)
- •Inspection Flow Chart
- •Oxygen Sensor-Incorrect Output Voltage (Service Code 94) (Europe Models)
- •Oxygen Sensor-Incorrect Output Voltage (Service Code 94) (Europe Models)
- •Ignition Switch off: Terminal 16 (br/w): 0 V
- •Needle Adapter Set: 57001-1457
- •Standard: Battery Voltage (12.8 V or more) for 3 seconds, and then 0 V.
- •Injector Output Voltage Connections to Injector #1
- •Injector Wiring Inspection
- •Injector Signal Test
- •Injector Resistance Inspection
- •Injector Resistance Connections to Injector
- •#1: W/r ←→ bl/r Terminal #2: w/r ←→ bl/g Terminal
- •Injector Unit Test
- •Injector Fuel Line Inspection
- •Injector Fuel Line Maximum Pressure Standard: 333 kPa (3.4 kgf/cm², 48 psi)
- •Idle Speed Inspection
- •Throttle Body Assy
- •Throttle Body Assy
- •Air Cleaner
- •Air Cleaner
- •Evaporative Emission Control System (California Model)
- •Evaporative Emission Control System (California Model)
- •Cooling System Table of Contents
- •Exploded View
- •Coolant Flow Chart
- •Specifications
- •Coolant
- •Coolant
- •Water Pump
- •Impeller Assembly
- •Thermostat
- •Thermostat
- •Hose and Pipes
- •Water Temperature Sensor
- •Engine Top End Table of Contents
- •Exhaust System
- •Exhaust System
- •Specifications
- •Special Tools and Sealant
- •Clean Air System
- •Clean Air System
- •Cylinder Head Cover
- •Cylinder Head Cover
- •Camshaft Chain Tensioner
- •Inlet 36.44 mm (1.4346 in.)
- •Valve Guide Removal
- •Valve Guide Installation
- •Valve-to-Guide Clearance Measurement (Wobble Method)
- •Throttle Body Holder
- •Muffler
- •Muffler
- •Clutch Table of Contents
- •Exploded View
- •Specifications
- •Clutch Lever and Cable
- •Clutch Lever and Cable
- •Clutch Cover
- •Engine Lubrication System Table of Contents
- •Exploded View
- •Engine Oil Flow Chart
- •Engine Oil and Oil Filter
- •Oil Pressure Relief Valve
- •Oil Pump
- •Oil Pump
- •Oil Pressure Measurement
- •Oil Pressure Switch
- •Engine Removal/Installation Table of Contents
- •Exploded View
- •Crankshaft/Transmission Table of Contents
- •Balancer
- •Balancer
- •Balancer Shaft Bearing Insert Selection
- •Ball Bearing, Needle Bearing, and Oil Seal
- •Wheels/Tires Table of Contents
- •Exploded View
- •Specifications
- •Service Limit:
- •Hub Bearing
- •Hub Bearing
- •Final Drive Table of Contents
- •Exploded View
- •Specifications
- •Inside Circlip Pliers: 57001-143
- •Brakes Table of Contents
- •Specifications
- •Inside Circlip Pliers: 57001-143
- •Brake Lever, Brake Pedal
- •Brake Disc
- •Brake Fluid
- •Inquiries to Rider
- •Sample Diagnosis Sheet
- •Service Code Table
- •Suspension Table of Contents
- •Specifications
- •Inside Circlip Pliers: 57001-143
- •Special Tools
- •Viscosity: kayaba khl34-g10 or equivalent
- •Inner Tube Inspection
- •Rear Shock Absorber
- •Special Tools - Jack: 57001-1238
- •Rear Shock Absorber
- •Jack Attachment: 57001-1608
- •Steering Table of Contents
- •Exploded View
- •Special Tools
- •Steering
- •Handlebar
- •Handlebar
- •Frame Table of Contents
- •Inner Fairing Removal
- •Inner Fairing Installation
- •Side Covers
- •Seat Covers
- •Fenders
- •Fenders
- •Sidestand
- •Frame Cover
- •Electrical System Table of Contents
- •Specifications
- •Parts Location
- •Parts Location
- •Wiring Diagram (Europe, Korea, Hong Kong and Kuwait)
- •Precautions
- •Electrical Wiring
- •Initial Charge
- •Interchange
- •Rotor Holder: 57001-1658
- •Interlock Operation Inspection
- •1St Check
- •2Nd Check
- •3Rd Check
- •Ic Igniter Inspection
- •Ignition System Circuit
- •Air Switching Valve
- •Air Switching Valve
- •Radiator Fan System
- •Indicator Lights Inspection
- •12 V 3.4 w Bulb (Other Side) → bl Lead Terminal Battery (–) → bk Lead Terminal
- •30 A Main Fuse Removal
- •15 A ecu Fuse Removal
- •Appendix Table of Contents
- •Engine Doesn’t Start, Starting Difficulty:
- •Poor Running at Low Speed:
- •Poor Running or No Power at High Speed:
- •Overheating:
- •Over Cooling:
- •Clutch Operation Faulty:
- •Gear Shifting Faulty:
- •Abnormal Engine Noise:
- •Valve noise:
- •Abnormal Drive Train Noise:
- •Battery Trouble:
- •Model application
Special Tools and Sealant
Kawasaki Bond (Silicone Sealant): 56019-120
Dfi Servicing Precautions
DFI Servicing Precautions
There are a number of important precautions that should be followed servicing the DFI system.
○This DFI system is designed to be used with a 12 V sealed
battery as its power source. Do not use any other battery
except for a 12 V sealed battery as a power source.
○Do not reverse the battery cable connections. This will
damage the ECU.
○To prevent damage to the DFI parts, do not disconnect the
battery cables or any other electrical connections when
the ignition switch is on or while the engine is running.
○Take care not to short the leads that are directly con-
nected to the battery positive (+) terminal to the chassis
ground.
○When charging, remove the battery from the motorcycle.
This is to prevent ECU damage by excessive voltage.
○Do not turn the ignition switch ON while any of the DFI
electrical connectors are disconnected. The ECU memo-
rizes service codes.
○Do not spray water on the electrical parts, DFI parts, con-
nectors, leads, and wiring.
○Whenever
the DFI electrical connections are to be dis- connected,
first turn
off the
ignition switch,
and disconnect the
battery (–)
terminal. Do
not pull
the lead,
only the
con- nector. Conversely, make sure that all the DFI electrical
connections are
firmly reconnected
before starting
the en- gine.
○Connect these connectors until they click [A]
○If a transceiver is installed on the motorcycle, make sure that the operation of the DFI system is not influenced by electric wave radiated from the antenna. Check operation of the system with the engine at idle. Locate the antenna as far as possible away from the ECU.
○When any fuel hose is disconnected, fuel may spout out
by residual pressure in the fuel line. Cover the hose joint
with a piece of clean cloth to prevent fuel spillage.
○When any fuel hose is disconnected, do not turn on the
ignition switch. Otherwise, the fuel pump will operate and
fuel will spout from the fuel hose.
○Do not operate the fuel pump if the pump is completely
dry. This is to prevent pump seizure.
○Before removing the fuel system parts, blow the outer sur-
faces of these parts clean with compressed air.
○To prevent corrosion and deposits in the fuel system, do
not add to fuel any fuel antifreeze chemicals.
Dfi Servicing Precautions
○To maintain the correct fuel/air mixture (F/A), there must be no inlet air leaks in the DFI system. Be sure to install the oil filler plug [A] after filling the engine oil.
Clutch Cover [B]
Torque - Oil Filler Plug: Hand-tighten
Outline
Outline
When an abnormality in the system occurs, the FI indi- cator light (LED) goes on to alert the rider on the meter panel. In addition, the condition of the problem is stored in the memory of the ECU (electronic control unit). With the engine stopped and turned in the self-diagnosis mode, the service code [A] is indicated by the number of times the FI indicator light (LED) blinks.
When
due to
a malfunction,
the FI
indicator light
(LED) re- mains
lit, ask
the rider
about the
conditions [B]
under which the
problem occurred and try to determine the cause
[C].
• First, conduct a self-diagnosis inspection and then a non
-self-diagnosis inspection. The non-self-diagnosis items
are not indicated by the FI indicator light (LED). Don’t rely solely on the DFI self-diagnosis function, use common sense.
Even
when the DFI system is operating normally, the FI indicator
light (LED)
[A] may
light up
under strong
electrical interference. No repair needed. Turn
the ignition switch OFF to stop the indicator
light.
When the FI indicator light (LED) goes on and the motor- cycle is brought in for repair, check the service codes.
When the repair has been done, the light (LED) doesn’t go on. But the service codes stored in memory are not erased to preserve the problem history, and the light (LED) can display the codes in the self-diagnosis mode. The problem history is referred when solving unstable problems.
When the motorcycle is down, the vehicle-down sensor is turned OFF and the ECU shuts off the fuel injectors and ignition system. The FI indicator light (LED) blinks but the service code cannot be displayed. The ignition switch is left ON. If the starter button is pushed, the electric starter turns but the engine doesn’t start. To start the engine again, raise the motorcycle, turn the ignition switch OFF, and then ON. The vehicle-down sensor is turned ON and the light (LED) goes OFF.
○The DFI part connectors [A] have seals [B], including the ECU.
•
Join the connector and insert the needle adapters
[C]
inside the seals [B] from behind the connector until the
adapter reaches the terminal.
Special
Tool - Needle Adapter Set: 57001-1457
• Make sure that measuring points are correct in the con-
nector, noting the position of the lock [D] and the lead
color before measurement. Do not reverse connections of the hand tester or a digital meter.
• Be careful not to short-circuit the leads of the DFI or elec-
trical system parts by contact between adapters.
•
Turn the
ignition switch ON and measure the voltage with the connector joined.
○After measurement, remove the needle adapters and ap- ply silicone sealant to the seals [A] of the connector [B] for waterproofing.
Sealant
- Kawasaki Bond (Silicone Sealant): 56019-120
• Always check battery condition before replacing the DFI parts. A fully charged battery is a must for conducting
accurate tests of the DFI system.
• Trouble may involve one or in some cases all items. Never replace a defective part without determining what
CAUSED the problem. If the problem was caused by some other item or items, they too must be repaired or replaced, or the new replacement part will soon fail again.
• Measure coil winding resistance when the DFI part is cold
(at room temperature).
• Make sure all connectors in the circuit are clean and tight, and examine wires for signs of burning, fraying, short,
etc. Deteriorated wires and bad connections can cause reappearance of problems and unstable operation of the DFI system.
If any wiring is deteriorated, replace the wiring.
•
Pull each connector [A] apart and inspect it for
corrosion, dirt, and damage.
If the connector is corroded or dirty, clean it carefully. If it is damaged, replace it. Connect the connectors securely.
• Check the wiring for continuity.
○Use the wiring diagram to find the ends of the lead which
is suspected of being a problem.
○Connect the hand tester between the ends of the leads.
○Set the tester to the × 1 Ω range, and read the tester.
If the tester does not read 0 Ω, the lead is defective. Re-
place the lead or the main harness or the sub harness.
○If
both ends of a harness [A] are far apart, ground
[B] the one end [C], using a jumper lead [D] and check the con-
tinuity between the end [E] and the ground [F]. This en- ables
to check
a long
harness for
continuity. If
the harness is
open, repair or replace the
harness.
○When
checking a harness [A] for short circuit, open one end [B] and
check the continuity between the other end [C] and ground [D]. If
there is continuity, the harness has a short circuit to ground, and
it must be repaired or re- placed.
• Narrow down suspicious locations by repeating the con- tinuity tests from the ECU connectors.
If no abnormality is found in the wiring or connectors, the DFI parts are the next likely suspects. Check the part, starting with input and output voltages. However, there is no way to check the ECU itself.
If an abnormality is found, replace the affected DFI part. If no abnormality is found in the wiring, connectors, and DFI parts, replace the ECU.
○Lead Color Codes:
BK: Black BL: Blue BR: Brown
CH: Chocolate DG: Dark Green
G: Green GY: Gray
LB: Light Blue LG: Light Green O: Orange
P: Pink PU: Purple R: Red
W: White Y: Yellow
○There
are two ways to inspect the DFI system. One is
voltage Check
Method and
the other
is Resistance
Check Method.
(Voltage Check Method)
○This method is conducted by measuring the input voltage
[B] to a sensor [A] first, and then the output voltage [C]
from the sensor.
○Sometimes this method can detect a fault of the ECU.
• Refer to each sensor inspection section for detail in this chapter.
• Use a fully charged battery and a digital meter [D] which
can be read two decimal places voltage or resistance.
(Resistance
Check Method)
○This method is simple. No need for a fully charged battery
and the needle adapter. Just do the following especially
when a sensor [A] is suspect.
• Turn the ignition switch OFF and disconnect the connec- tors.
• Inspect the sensor resistance, using a digital meter (see
each sensor inspection).
• Inspect the wiring and connectors [B] for continuity, using the hand tester [C] (analog tester) rather than a digital
meter.
Special Tool - Hand Tester: 57001-1394
If the sensor, the wiring and connections are good, inspect the ECU for its ground and power supply (see ECU Power Supply Inspection). If the ground and power supply are good, the ECU is suspect. Replace the ECU.
DFI
Diagnosis Flow Chart
