- •Table of Contents
- •INTRODUCTION TO THE DSP56002
- •DSP56002 PIN DESCRIPTIONS
- •PORT A
- •PORT B
- •PORT C
- •PROGRAMMING SHEETS
- •List of Figures
- •List of Tables
- •1.1 INTRODUCTION
- •Figure 1-1 DSP56002 Technical Literature
- •1.2 FEATURES
- •Zero Overhead Nested DO Loops
- •512 x 24 Program RAM
- •Two 256 x 24 Data RAM
- •Two 256 x 24 Data ROM (Sine and Cosine Tables)
- •Synchronous Serial Interface Port
- •24 General Purpose I/O Pins
- •24-bit Timer/Event Counter
- •1.3 DSP56K CENTRAL PROCESSING UNIT OVERVIEW
- •Data Buses
- •Address Buses
- •Data Arithmetic Logic Unit (data ALU)
- •Address Generation Unit (AGU)
- •Program Control Unit (PCU)
- •Memory Expansion (Port A)
- •Figure 1-2 DSP56002 Block Diagram
- •1.4 MANUAL ORGANIZATION
- •INTRODUCTION TO THE DSP56002
- •2.1 INTRODUCTION
- •2.2 SIGNAL DESCRIPTIONS
- •Figure 2-1 DSP56002 Signals
- •2.2.1 Port A Address and Data Bus
- •2.2.2 Port A Bus Control
- •Table 2-1 Program and Data Memory Select Encoding
- •2.2.3 Interrupt and Mode Control
- •2.2.4 Power and Clock
- •2.2.5 Host Interface
- •2.2.6 Serial Communication Interface (SCI)
- •2.2.7 Synchronous Serial Interface (SSI)
- •2.3 ON-CHIP EMULATION (OnCE) PINS
- •2.3.1 Debug Serial Input/Chip Status 0 (DSI/OS0)
- •2.3.2 Debug Serial Clock/Chip Status 1 (DSCK/OS1)
- •2.3.3 Debug Serial Output (DSO)
- •2.3.4 Debug Request Input (DR)
- •2.4 PLL PINS
- •2.5 TIMER/EVENT COUNTER MODULE PIN
- •SECTION 2
- •DSP56002 PIN DESCRIPTIONS
- •3.1 MEMORY MODULES AND OPERATING MODES
- •3.2 DSP56002 DATA AND PROGRAM MEMORY
- •3.2.1 Program Memory
- •3.2.2 X Data Memory
- •3.2.3 Y Data Memory
- •Figure 3-1 DSP56002 Memory Maps
- •3.3 DSP56002 OPERATING MODE REGISTER (OMR)
- •3.3.1 Chip Operating Mode (Bits 0 and 1)
- •Figure 3-2 OMR Format
- •3.3.2 Data ROM Enable (Bit 2)
- •3.3.3 Internal Y Memory Disable Bit (Bit 3)
- •Table 3-1 Memory Mode Bits
- •3.3.4 Chip Operating Mode (Bit 4)
- •3.3.5 Reserved (Bit 5)
- •3.3.6 Stop Delay (Bit 6)
- •3.4 DSP56002 OPERATING MODES
- •Table 3-2 DSP56002 Operating Mode Summary
- •3.4.1 Single Chip Mode (Mode 0)
- •3.4.2 Bootstrap From EPROM (Mode 1)
- •Figure 3-3 Port A Bootstrap Circuit
- •Table 3-3 Organization of EPROM Data Contents
- •3.4.3 Normal Expanded Mode (Mode 2)
- •3.4.4 Development Mode (Mode 3)
- •3.4.5 Reserved (Mode 4)
- •3.4.6 Bootstrap From Host (Mode 5)
- •3.4.7 Bootstrap From SCI (Mode 6)
- •3.4.8 Reserved (Mode 7)
- •3.5 DSP56002 INTERRUPT PRIORITY REGISTER
- •Table 3-4 Interrupt Vectors
- •Table 3-5 Exception Priorities Within an IPL
- •SECTION 3
- •4.1 INTRODUCTION
- •4.2 PORT A INTERFACE
- •Figure 4-1 Port A Signals
- •Figure 4-2 External Program Space
- •Figure 4-3 External X and Y Data Space
- •Figure 4-4 Memory Segmentation
- •Table 4-1 Program and Data Memory Select Encoding
- •4.3 PORT A TIMING
- •Figure 4-8 Mixed-Speed Expanded System
- •4.4 PORT A WAIT STATES
- •Table 4-2 Wait State Control
- •4.5 BUS CONTROL REGISTER (BCR)
- •Figure 4-9 Bus Control Register
- •Figure 4-10 Bus Strobe/Wait Sequence
- •4.6 BUS STROBE AND WAIT PINS
- •4.7 BUS ARBITRATION AND SHARED MEMORY
- •Figure 4-11 Bus Request/Bus Grant Sequence
- •Table 4-3 BR and BG During WAIT
- •1. DSP# 2 sets OUT1=0 (BR#1=0).
- •4.7.4 Signaling Using Semaphores
- •Figure 4-17 Signaling Using Semaphores
- •5.1 INTRODUCTION
- •Figure 5-1 Port B Interface
- •5.2 GENERAL PURPOSE I/O CONFIGURATION
- •Figure 5-2 Parallel Port B Registers
- •Figure 5-3 Parallel Port B Pinout
- •Figure 5-4 Port B I/O Pin Control Logic
- •5.2.1 Programming General Purpose I/O
- •Figure 5-5 On-Chip Peripheral Memory Map
- •5.2.2 Port B General Purpose I/O Timing
- •Figure 5-7 I/O Port B Configuration
- •5.3 HOST INTERFACE (HI)
- •Figure 5-8 HI Block Diagram
- •5.3.1 Host Interface – DSP CPU Viewpoint
- •5.3.2 Programming Model – DSP CPU Viewpoint
- •5.3.2.1 Host Control Register (HCR)
- •5.3.2.1.4 HCR Host Flag 2 (HF2) Bit 3
- •5.3.2.1.5 HCR Host Flag 3 (HF3) Bit 4
- •5.3.2.1.6 HCR Reserved Control (Bits 5, 6, and 7)
- •5.3.2.2 Host Status Register (HSR)
- •5.3.2.2.1 HSR Host Receive Data Full (HRDF) Bit 0
- •5.3.2.2.3 HSR Host Command Pending (HCP) Bit 2
- •5.3.2.2.4 HSR Host Flag 0 (HF0) Bit 3
- •5.3.2.2.5 HSR Host Flag 1 (HF1) Bit 4
- •Figure 5-10 Host Flag Operation
- •5.3.2.2.6 HSR Reserved Status (Bits 5 and 6)
- •5.3.2.2.7 HSR DMA Status (DMA) Bit 7
- •5.3.2.3 Host Receive Data Register (HRX)
- •5.3.2.4 Host Transmit Data Register (HTX)
- •5.3.2.5 Register Contents After Reset
- •5.3.2.6 Host Interface DSP CPU Interrupts
- •Figure 5-11 HSR–HCR Operation
- •5.3.2.7 Host Port Usage Considerations – DSP Side
- •5.3.3 Host Interface – Host Processor Viewpoint
- •Figure 5-13 HI Register Map
- •5.3.3.2 Interrupt Control Register (ICR)
- •5.3.3.2.1 ICR Receive Request Enable (RREQ) Bit 0
- •5.3.3.2.3 ICR Reserved Bit (Bit 2)
- •Table 5-2 HREQ Pin Definition
- •5.3.3.2.4 ICR Host Flag 0 (HF0) Bit 3
- •5.3.3.2.5 ICR Host Flag 1 (HF1) Bit 4
- •Table 5-3 Host Mode Bit Definition
- •5.3.3.2.7 ICR Initialize Bit (INIT) Bit 7
- •Table 5-4 HREQ Pin Definition
- •5.3.3.3 Command Vector Register (CVR)
- •Figure 5-14 Command Vector Register
- •5.3.3.3.2 CVR Reserved Bit (Bit 6)
- •5.3.3.3.3 CVR Host Command Bit (HC) Bit 7
- •5.3.3.4 Interrupt Status Register (ISR)
- •5.3.3.4.3 ISR Transmitter Ready (TRDY) Bit 2
- •5.3.3.4.4 ISR Host Flag 2 (HF2) Bit 3
- •5.3.3.4.5 ISR Host Flag 3 (HF3) Bit 4
- •5.3.3.4.6 ISR Reserved Bit (Bit 5)
- •5.3.3.4.7 ISR DMA Status (DMA) Bit 6
- •5.3.3.4.8 ISR Host Request (HREQ) Bit 7
- •5.3.3.5 Interrupt Vector Register (IVR)
- •5.3.3.6 Receive Byte Registers (RXH, RXM, RXL)
- •5.3.3.7 Transmit Byte Registers (TXH, TXM, TXL)
- •5.3.3.8 Registers After Reset
- •Table 5-5 Host Registers after Reset (Host Side)
- •5.3.4 Host Interface Pins
- •5.3.4.3 Host Read/Write (HR/W)
- •5.3.4.4 Host Enable (HEN)
- •5.3.4.5 Host Request (HREQ)
- •Table 5-6 Port B Pin Definitions
- •5.3.4.6 Host Acknowledge (HACK)
- •5.3.5 Servicing the Host Interface
- •Figure 5-15 Host Processor Transfer Timing
- •1. Polling
- •2. Interrupts, which can be either
- •5.3.5.1 HI Host Processor Data Transfer
- •5.3.5.2 HI Interrupts Host Request (HREQ)
- •Figure 5-16 Interrupt Vector Register Read Timing
- •5.3.5.3 Polling
- •Figure 5-17 HI Interrupt Structure
- •Figure 5-18 DMA Transfer Logic and Timing
- •5.3.5.5 Servicing DMA Interrupts
- •5.3.6 HI Application Examples
- •5.3.6.1 HI Initialization
- •Figure 5-19 HI Initialization Flowchart
- •Figure 5-20 HI Initialization–DSP Side
- •Figure 5-21 (a) HI Configuration–Host Side
- •Figure 5-22 Host Mode and INIT Bits
- •2. Assert HACK If the interface is using HACK
- •5. Assert HEN to enable the HI
- •5.3.6.2.1 Host to DSP - Data Transfer
- •Figure 5-23 Bits Used for Host-to-DSP Transfer
- •Figure 5-24 Data Transfer from Host to DSP
- •5. Writing data to TXL clears TXDE in the ISR.
- •5.3.6.2.2 Host to DSP – Command Vector
- •Figure 5-27 HI Exception Vector Locations
- •Figure 5-28 Host Command
- •2. The HC is then set.
- •3. The HCP bit in the HSR is set when HC is set.
- •Figure 5-25 Receive Data from Host–Main Program
- •Figure 5-29 Bootstrap Using the HI
- •Figure 5-30 Transmit/Receive Byte Registers
- •Figure 5-31 Bootstrap Code Fragment
- •5.3.6.2.4 DSP to Host Data Transfer
- •Figure 5-32 Bits Used for DSP to Host Transfer
- •Figure 5-33 Data Transfer from DSP to Host
- •5.3.6.3 DMA Data Transfer
- •Figure 5-36 HI Hardware–DMA Mode
- •5.3.6.3.1 Host To DSP Internal Processing
- •1. HI asserts the HREQ pin when TXDE=1.
- •Figure 5-37 DMA Transfer and Host Interrupts
- •3. When HACK is asserted, the HI deasserts HREQ.
- •Figure 5-39 Host-to-DSP DMA Procedure
- •Figure 5-38 Host Bits with TREQ and RREQ
- •5.3.6.3.2 Host to DSP DMA Procedure
- •5.3.6.3.3 DSP to Host Internal Processing
- •5.3.6.3.4 DSP to Host DMA Procedure
- •Figure 5-40 DSP to Host DMA Procedure
- •5.3.6.4 Example Circuits
- •Figure 5-41 MC68HC11 to DSP56002 Host Interface
- •Figure 5-42 MC68000 to DSP56002 Host Interface
- •Figure 5-43 Multi-DSP Network Example
- •2. Overwriting Transmit Byte Registers:
- •4. Overwriting the Host Vector:
- •5. Cancelling a Pending Host Command Exception:
- •6.1 INTRODUCTION
- •Figure 6-1 Port C Interface
- •6.2 GENERAL-PURPOSE I/O (PORT C)
- •Figure 6-2 Port C GPIO Control
- •Figure 6-3 Port C GPIO Registers
- •Figure 6-4 Port C I/O Pin Control Logic
- •6.2.1 Programming General Purpose I/O
- •Figure 6-6 Write/Read Parallel Data with Port C
- •Figure 6-7 I/O Port C Configuration
- •6.2.2 Port C General Purpose I/O Timing
- •6.3 SERIAL COMMUNICATION INTERFACE (SCI)
- •6.3.1 SCI I/O Pins
- •6.3.1.1 Receive Data (RXD)
- •6.3.1.2 Transmit Data (TXD)
- •6.3.1.3 SCI Serial Clock (SCLK)
- •6.3.2 SCI Programming Model
- •Figure 6-9 SCI Programming Model
- •6.3.2.1 SCI Control Register (SCR)
- •Figure 6-10 Serial Formats (Sheet 1 of 2)
- •Table 6-1 Word Formats
- •6.3.2.1.2 SCR SCI Shift Direction (SSFTD) Bit 3
- •6.3.2.1.3 SCR Send Break (SBK) Bit 4
- •6.3.2.1.4 SCR Wakeup Mode Select (WAKE) Bit 5
- •6.3.2.1.5 SCR Receiver Wakeup Enable (RWU) Bit 6
- •6.3.2.1.7 SCR Receiver Enable (RE) Bit 8
- •6.3.2.1.8 SCR Transmitter Enable (TE) Bit 9
- •6.3.2.1.14 SCR SCI Clock Polarity (SCKP) Bit 15
- •6.3.2.2 SCI Status Register (SSR)
- •6.3.2.2.1 SSR Transmitter Empty (TRNE) Bit 0
- •6.3.2.2.4 SSR Idle Line Flag (IDLE) Bit 3
- •6.3.2.2.5 SSR Overrun Error Flag (OR) Bit 4
- •6.3.2.2.6 SSR Parity Error (PE) Bit 5
- •6.3.2.2.7 SSR Framing Error Flag (FE) Bit 6
- •6.3.2.2.8 SSR Received Bit 8 Address (R8) Bit 7
- •6.3.2.3 SCI Clock Control Register (SCCR)
- •Figure 6-11 16 x Serial Clock
- •6.3.2.3.2 SCCR Clock Out Divider (COD) Bit 12
- •6.3.2.3.3 SCCR SCI Clock Prescaler (SCP) Bit 13
- •Figure 6-12 SCI Baud Rate Generator
- •6.3.2.4 SCI Data Registers
- •6.3.2.4.1 SCI Receive Registers
- •Figure 6-13 Data Packing and Unpacking
- •6.3.2.4.2 SCI Transmit Registers
- •6.3.3 Register Contents After Reset
- •6.3.4 SCI Initialization
- •Figure 6-14 SCI Initialization Procedure
- •6.3.5 SCI Exceptions
- •Figure 6-16 SCI Exception Vector Locations
- •6.3.6 Synchronous Data
- •Figure 6-18 Synchronous Slave
- •Figure 6-19 Synchronous Timing
- •Figure 6-20 SCI Synchronous Transmit
- •Figure 6-21 SCI Synchronous Receive
- •6.3.7 Asynchronous Data
- •6.3.7.1 Asynchronous Data Reception
- •6.3.7.2 Asynchronous Data Transmission
- •Figure 6-27 Transmitting Marks and Spaces
- •6.3.8 Multidrop
- •6.3.8.1 Transmitting Data and Address Characters
- •6.3.8.3 Idle Line Wakeup
- •Figure 6-32 Idle Line Wakeup
- •6.3.8.4 Address Mode Wakeup
- •6.3.8.5 Multidrop Example
- •6.3.9 SCI Timer
- •Figure 6-35 SCI Timer Operation
- •Figure 6-36 SCI Timer Example (Sheet 1 of 2)
- •Figure 6-37 DSP56002 Bootstrap Example - Mode 6
- •Figure 6-38 Bootstrap Code Fragment
- •6.3.11 Example Circuits
- •Figure 6-39 Synchronous Mode Example
- •Figure 6-41 Multimaster System Example
- •Figure 6-40 Master-Slave System Example
- •6.4 SYNCHRONOUS SERIAL INTERFACE (SSI)
- •6.4.1 SSI Data and Control Pins
- •6.4.1.1 Serial Transmit Data Pin (STD)
- •6.4.1.2 Serial Receive Data Pin (SRD)
- •6.4.1.3 Serial Clock (SCK)
- •6.4.1.4 Serial Control Pin (SC0)
- •Table 6-7 SSI Operation: Flag 0 and Rx Clock
- •6.4.1.5 Serial Control Pin (SC1)
- •Table 6-8 SSI Operation: Flag 1 and Rx Frame Sync
- •6.4.1.6 Serial Control Pin (SC2)
- •Table 6-9 SSI Operation: Tx and Rx Frame Sync
- •6.4.2 SSI Programming Model
- •Figure 6-45 SSI Programming Model (Sheet 1 of 2)
- •6.4.2.1 SSI Control Register A (CRA)
- •Table 6-10 Number of Bits/Word
- •6.4.2.1.4 CRA Prescaler Range (PSR) Bit 15
- •6.4.2.2 SSI Control Register B (CRB)
- •6.4.2.2.1 CRB Serial Output Flag 0 (OF0) Bit 0
- •6.4.2.2.2 CRB Serial Output Flag 1 (OF1) Bit 1
- •Figure 6-46 Serial Control, Direction Bits
- •6.4.2.2.6 CRB Clock Source Direction (SCKD) Bit 5
- •6.4.2.2.7 CRB Shift Direction (SHFD) Bit 6
- •Table 6-11 Frame Sync Length
- •6.4.2.2.9 CRB Sync/Async (SYN) Bit 9
- •6.4.2.2.10 CRB Gated Clock Control (GCK) Bit 10
- •6.4.2.2.11 CRB SSI Mode Select (MOD) Bit 11
- •6.4.2.2.12 CRB SSI Transmit Enable (TE) Bit 12
- •6.4.2.2.13 CRB SSI Receive Enable (RE) Bit 13
- •6.4.2.3 SSI Status Register (SSISR)
- •6.4.2.3.1 SSISR Serial Input Flag 0 (IF0) Bit 0
- •6.4.2.3.2 SSISR Serial Input Flag 1 (IF1) Bit 1
- •6.4.2.3.9 SSI Receive Shift Register
- •Figure 6-47 Receive Data Path
- •6.4.2.3.10 SSI Receive Data Register (RX)
- •6.4.2.3.11 SSI Transmit Shift Register
- •Figure 6-48 Transmit Data Path
- •6.4.2.3.12 SSI Transmit Data Register (TX)
- •6.4.2.3.13 Time Slot Register (TSR)
- •6.4.3 Operational Modes and Pin Definitions
- •6.4.4 Registers After Reset
- •Table 6-14 SSI Registers After Reset
- •6.4.5 SSI Initialization
- •Figure 6-49 SSI Initialization Block Diagram
- •Figure 6-50 SSI CRA Initialization Procedure
- •Figure 6-51 SSI CRB Initialization Procedure
- •Figure 6-52 SSI Initialization Procedure
- •6.4.6 SSI Exceptions
- •Figure 6-53 SSI Exception Vector Locations
- •Figure 6-54 SSI Exceptions
- •Table 6-17 SSI Operating Modes
- •6.4.7.1 Data/Operation Formats
- •6.4.7.1.1 Normal/Network Mode Selection
- •6.4.7.1.2 Continuous/Gated Clock Selection
- •Figure 6-58 CRB GCK Bit Operation
- •Figure 6-62 Synchronous Communication
- •Figure 6-63 CRB SYN Bit Operation
- •Figure 6-64 Gated Clock — Synchronous Operation
- •6.4.7.1.4 Frame Sync Selection
- •Figure 6-68 CRB FSL0 and FSL1 Bit Operation
- •6.4.7.1.5 Shift Direction Selection
- •Figure 6-71 CRB SHFD Bit Operation (Sheet 1 of 2)
- •6.4.7.2 Normal Mode Examples
- •6.4.7.2.1 Normal Mode Transmit
- •Figure 6-72 Normal Mode Example
- •2. SC2 is TX and RX frame sync out
- •3. STD is transmit data out
- •4. SCK clocks the transmit data out
- •6.4.7.2.2 Normal Mode Receive
- •6.4.7.3 Network Mode Examples
- •Figure 6-75 Network Mode Example
- •Figure 6-76 TDM Network Software Flowchart
- •Figure 6-77 Network Mode Initialization
- •6.4.7.3.1 Network Mode Transmit
- •6.4.7.3.2 Network Mode Receive
- •Figure 6-80 On Demand Example
- •Figure 6-81 On-Demand Data-Driven Network Mode
- •Figure 6-82 Clock Modes
- •Figure 6-83 SPI Configuration
- •6.4.8 Flags
- •Figure 6-88 Output Flag Example
- •Figure 6-89 Output Flag Initialization
- •Figure 6-90 Input Flags
- •6.4.9 Example Circuits
- •Figure 6-91 SSI Cascaded Multi-DSP System
- •Figure 6-92 SSI TDM Parallel DSP Network
- •Figure 6-96 SSI TDM Bus DSP Network
- •SECTION 6
- •PORT C
- •7.1 INTRODUCTION
- •7.2 TIMER/EVENT COUNTER BLOCK DIAGRAM
- •Figure 7-2 Timer/Event Counter Programming Model
- •7.3 TIMER COUNT REGISTER (TCR)
- •7.4 TIMER CONTROL/STATUS REGISTER (TCSR)
- •7.4.1 Timer Enable (TE) Bit 0
- •7.4.2 Timer Interrupt Enable (TIE) Bit 1
- •7.4.3 Inverter (INV) Bit 2
- •Table 7-1 Timer/Event Counter Control Bits
- •GPIO*
- •Internal
- •Timer (Mode 0)
- •Output
- •Internal
- •Timer Pulse (Mode 1)
- •Output
- •Internal
- •Timer Toggle (Mode 2)
- •Reserved - Do Not Use
- •Input
- •Internal
- •Input Width (Mode 4)
- •Input
- •Internal
- •Input Period (Mode 5)
- •Input
- •External
- •Standard Time Counter (Mode 6)
- •Input
- •External
- •Event Counter (Mode 7)
- •7.4.5 General Purpose I/O (GPIO) Bit 6
- •7.4.6 Timer Status (TS) Bit 7
- •7.4.7 Direction (DIR) Bit 8
- •7.4.8 Data Input (DI) Bit 9
- •7.4.9 Data Output (DO) Bit 10
- •7.4.10 TCSR Reserved bits (Bits 11-23)
- •7.5 TIMER/EVENT COUNTER MODES OF OPERATION
- •Figure 7-3 Standard Timer Mode (Mode 0)
- •Figure 7-4 Timer/Event Counter Disable
- •7.5.4 Timer Mode 4 (Pulse Width Measurement Mode)
- •Figure 7-8 Pulse Width Measurement Mode (INV=0)
- •Figure 7-9 Pulse Width Measurement Mode (INV=1)
- •7.5.5 Timer Mode 5 (Period Measurement Mode)
- •Figure 7-10 Period Measurement Mode (INV=0)
- •Figure 7-11 Period Measurement Mode (INV=1)
- •7.7 OPERATING CONSIDERATIONS
- •7.8 SOFTWARE EXAMPLES
- •7.8.1 General Purpose I/O Input
- •7.8.2 General Purpose I/O Output
- •7.8.4 Pulse Width Measurement Mode (Timer Mode 4)
- •7.8.5 Period Measurement Mode (Timer Mode 5)
- •A.1 INTRODUCTION
- •Table B-2 Instruction Set Summary — Sheet 1 of 5
- •Figure B-2 Status Register (SR)
- •Figure B-3 Bus Control Register (BCR)
- •Figure B-7 Port B Control Register (PBC)
- •Figure B-8 Port B Data Direction Register (PBDDR)
- •Figure B-9 Port B Data Register (PBD)
- •Figure B-10 Port C Control Register (PCC)
- •Figure B-12 Port C Data Register (PCD)
- •Figure B-17 Host Transmit Data Register (HTX)
- •Figure B-13 Port B Control Register (PBC)
- •Figure B-14 Host Control Register (HCR)
- •Figure B-16 Host Receive Data Register (HRX)
- •Figure B-15 Host Status Register (HSR)
- •Figure B-19 Command Vector Register (CVR)
- •Figure B-18 Interrupt Control Register (ICR)
- •Figure B-20 Interrupt Status Register (ISR)
- •Figure B-21 Interrupt Vector Register (IVR)
- •Figure B-24 Port C Control Register (PCC)
- •Figure B-25 SCI Control Register (SCR)
- •Figure B-27 SCI Clock Control Register (SCCR)
- •Figure B-29 SCI Receive Data Registers
- •Figure B-28 SCI Transmit Data Registers
- •Figure B-30 SSI Control Register (PCC)
- •Figure B-31 SSI Control Register A (CRA)
- •Figure B-32 SSI Control Register B (CRB)
- •Figure B-33 SSI Status Register (SSISR)
- •Figure B-35 Timer Count Register (TCR)
- •INDEX
Freescale Semiconductor, Inc.
Freescale Semiconductor, Inc.
SERIAL COMMUNICATION INTERFACE (SCI)
6.3.2.1.14SCR SCI Clock Polarity (SCKP) Bit 15
The clock polarity, sourced or received on the clock pin (SCLK), can be inverted using this bit, eliminating the need for an external inverter. When bit 15 equals zero, the clock polarity is positive; when bit 15 equals one, the clock polarity is negative. In the synchronous mode, positive polarity means that the clock is normally positive and transitions negative during data valid; whereas, negative polarity means that the clock is normally negative and transitions positive during valid data. In the asynchronous mode, positive polarity means that the rising edge of the clock occurs in the center of the period that data is valid; negative polarity means that the falling edge of the clock occurs during the center of the period that data is valid. SCKP is cleared on hardware and software reset.
6.3.2.2SCI Status Register (SSR)
The SSR is an 8-bit read-only register used by the DSP CPU to determine the status of the SCI. When the SSR is read onto the internal data bus, the register contents occupy the low-order byte of the data bus and all high-order portions are zero filled. The status bits are described in the following paragraphs.
6.3.2.2.1SSR Transmitter Empty (TRNE) Bit 0
The TRNE flag is set when both the transmit shift register and data register are empty to indicate that there is no data in the transmitter. When TRNE is set, data written to one of the three STX locations or to the STXA will be transferred to the transmit shift register and be the first data transmitted. TRNE is cleared when TDRE is cleared by writing data into the transmit data register (STX) or the transmit data address register (STXA), or when an idle, preamble, or break is transmitted. The purpose of this bit is to indicate that the transmitter is empty; therefore, the data written to STX or STXA will be transmitted next – i.e., there is not a word in the transmit shift register presently being transmitted. This procedure is useful when initiating the transfer of a message (i.e., a string of characters). TRNE is set by the hardware, software, SCI individual, and stop reset.
6.3.2.2.2SSR Transmit Data Register Empty (TDRE) Bit 1
The TDRE bit is set when the SCI transmit data register is empty. When TDRE is set, new data may be written to one of the SCI transmit data registers (STX) or transmit data address register (STXA). TDRE is cleared when the SCI transmit data register is written. TDRE is set by the hardware, software, SCI individual, and stop reset.
In the SCI synchronous mode, when using the internal SCI clock, there is a delay of up to 5.5 serial clock cycles between the time that STX is written until TDRE is set, indicating the data has been transferred from the STX to the transmit shift register. There is a two to four serial clock cycle delay between writing STX and loading the transmit shift register;
6 - 22 PORT C MOTOROLA
For More Information On This Product, Go to: www.freescale.com
Freescale Semiconductor, Inc.
Freescale Semiconductor, Inc.
SERIAL COMMUNICATION INTERFACE (SCI)
in addition, TDRE is set in the middle of transmitting the second bit. When using an external serial transmit clock, if the clock stops, the SCI transmitter stops. TDRE will not be set until the middle of the second bit transmitted after the external clock starts. Gating the external clock off after the first bit has been transmitted will delay TDRE indefinitely.
In the SCI asynchronous mode, the TDRE flag is not set immediately after a word is transferred from the STX or STXA to the transmit shift register nor when the word first begins to be shifted out. TDRE is set two cycles of the 16× clock after the start bit – i.e., two 16× clock cycles into to transmission time of the first data bit.
6.3.2.2.3SSR Receive Data Register Full (RDRF) Bit 2
The RDRF bit is set when a valid character is transferred to the SCI receive data register from the SCI receive shift register. RDRF is cleared when the SCI receive data register is read or by the hardware, software, SCI individual, and stop reset.
6.3.2.2.4SSR Idle Line Flag (IDLE) Bit 3
IDLE is set when 10 (or 11) consecutive ones are received. IDLE is cleared by a start-bit detection. The IDLE status bit represents the status of the receive line. The transition of IDLE from zero to one can cause an IDLE interrupt (ILIE). IDLE is cleared by the hardware, software, SCI individual, and stop reset.
6.3.2.2.5SSR Overrun Error Flag (OR) Bit 4
The OR flag is set when a byte is ready to be transferred from the receive shift register to the receive data register (SRX) that is already full (RDRF=1). The receive shift register data is not transferred to the SRX. The OR flag indicates that character(s) in the receive data stream may have been lost. The only valid data is located in the SRX. OR is cleared when the SCI status register is read, followed by a read of SRX. The OR bit clears the FE and PE bits – i.e., overrun error has higher priority than FE or PE. OR is cleared by the hardware, software, SCI individual, and stop reset.
6.3.2.2.6SSR Parity Error (PE) Bit 5
In the 11-bit asynchronous modes, the PE bit is set when an incorrect parity bit has been detected in the received character. It is set simultaneously with RDRF for the byte which contains the parity error – i.e., when the received word is transferred to the SRX. If PE is set, it does not inhibit further data transfer into the SRX. PE is cleared when the SCI status register is read, followed by a read of SRX. PE is also cleared by the hardware, software,
SCI individual, or stop reset. In the 10-bit asynchronous mode, the 11-bit multidrop mode,
MOTOROLA PORT C 6 - 23
For More Information On This Product, Go to: www.freescale.com